参数资料
| 型号： | XRT83VSH28IB |
| 厂商： | Exar Corporation |
| 文件页数： | 74/75页 |
| 文件大小： | 0K |
| 描述： | IC LIU SH E1 OCTAL 225BGA |
| 标准包装： | 84 |
| 类型： | 线路接口装置（LIU） |
| 驱动器/接收器数： | 8/8 |
| 规程： | T1，E1，J1 |
| 电源电压： | 3.14 V ~ 3.47 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 225-BGA |
| 供应商设备封装： | 225-BGA（19x19） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页当前第74页第75页
XRT83VSH28
5
8-CHANNEL E1 SHORT-HAUL LINE INTERFACE UNIT
REV. 2.0.0
PIN DESCRIPTION BY FUNCTION
RECEIVE SECTION
SIGNAL NAME
BGA
LEAD #
TYPE
DESCRIPTION
RXON
K16
I
Receiver On
Hardware Mode Only
This pin is used to enable the receivers for all channels. By default, the receivers
are turned ON in hardware mode. To turn the receivers OFF, pull this pin "Low".
NOTE: Internally pulled "High" with a 50k
resistor.
RLOS0
RLOS1
RLOS2
RLOS3
RLOS4
RLOS5
RLOS6
RLOS7
C3
H4
H15
A16
V3
L2
J15
T15
O
Receive Loss of Signal
When a receive loss of signal occurs according to ITU-T G.775, the RLOS pin will go
"High" for a minimum of one RCLK cycle. RLOS will remain "High" until the loss of
signal condition clears. See the Receive Loss of Signal section of this datasheet for
more details.
NOTE: This pin can be used for redundancy applications to initiate an automatic
switch to a backup card.
RCLK0
RCLK1
RCLK2
RCLK3
RCLK4
RCLK5
RCLK6
RCLK7
B3
H3
H16
A17
U3
L3
M15
U16
O
Receive Clock Output
RCLK is the recovered clock from the incoming data stream. If the incoming signal
is absent or RTIP/RRING are in "High-Z", RCLK maintains its timing by using an
internal master clock as its reference. RPOS/RNEG data can be updated on either
edge of RCLK selected by RCLKE.
NOTE: RCLKE is a global setting that applies to all 8 channels.
RNEG/LCV0
RNEG/LCV1
RNEG/LCV2
RNEG/LCV3
RNEG/LCV4
RNEG/LCV5
RNEG/LCV6
RNEG/LCV7
A2
H2
H18
B16
T4
M4
M16
V17
O
RNEG/LCV_OF Output
In dual rail mode, this pin is the receive negative data output. In single rail mode,
this pin is a Line Code Violation / Counter Overflow indicator. If LCV is selected by
programming the appropriate global register and if a line code violation, a bi-polar
violation, or excessive zeros occur, the LCV pin will pull "High" for a minimum of one
RCLK cycle. LCV will remain "High" until there are no more violations. However, if
OF (Overflow) is selected the LCV pin will pull "High" if the internal LCV counter is
saturated. The LCV pin will remain "High" until the LCV counter is reset.
RPOS0
RPOS1
RPOS2
RPOS3
RPOS4
RPOS5
RPOS6
RPOS7
B2
G2
D15
B17
U2
M3
L17
T17
O
RPOS/RDATA Output
Receive digital output pin. In dual rail mode, this pin is the receive positive data out-
put. In single rail mode, this pin is the receive non-return to zero (NRZ) data output.
相关PDF资料 |
PDF描述 |
|---|---|
| XRT83VSH314IB-F | IC LIU SH T1/E1/J1 14CH 304TBGA |
| XRT83VSH316IB | IC LIU SH T1/E1/J1 16CH 316STBGA |
| XRT83VSH38IB | IC LIU SH T1/E1/J1 8CH 225BGA |
| XRT85L61IG | IC BITS CLOCK EXTRACTOR 28TSSOP |
| XRT91L30IQ | IC TXRX SONET/SDH 8BIT 64QFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XRT83VSH28IB-F | 功能描述:外围驱动器与原件 - PCI 8 Channel 1.8V-3.3V temp -45 to 85C RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| XRT83VSH28IB-F | 制造商:Exar Corporation 功能描述:T1/E1 LIU IC |
| XRT83VSH314 | 制造商:EXAR 制造商全称:EXAR 功能描述:14-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT |
| XRT83VSH314ES | 功能描述:外围驱动器与原件 - PCI 14 CHT1/E1LIUSH LOW COST VERSION RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| XRT83VSH314IB | 功能描述:接口 - 专用 14 CH, SH T1/E1 1.8V DGTL/3.3V ANLG RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
发布紧急采购，3分钟左右您将得到回复。