参数资料
| 型号： | XRT83VSH28IB |
| 厂商： | Exar Corporation |
| 文件页数： | 5/75页 |
| 文件大小： | 0K |
| 描述： | IC LIU SH E1 OCTAL 225BGA |
| 标准包装： | 84 |
| 类型： | 线路接口装置（LIU） |
| 驱动器/接收器数： | 8/8 |
| 规程： | T1，E1，J1 |
| 电源电压： | 3.14 V ~ 3.47 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 225-BGA |
| 供应商设备封装： | 225-BGA（19x19） |
| 包装： | 托盘 |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页
XRT83VSH28
10
REV. 2.0.0
8-CHANNEL E1 SHORT-HAUL LINE INTERFACE UNIT
PARALLEL MICROPROCESSOR INTERFACE
SIGNAL NAME
BGA
LEAD
#
TYPE
DESCRIPTION
HW/HOST
T10
I
Mode Control Input
This pin is used to select Host mode or Hardware mode. By default, the LIU is set in
Hardware mode. To use Host mode, this pin must be pulled "Low".
NOTE: Internally pulled “High” with a 50k
resistor.
WR_R/W/EQC0
D7
I
Write Input(R/W)/Equalizer Control Signal 0
Host Mode
This pin is used to communicate a Read or Write operation according to the which
microprocessor is chosen.
See the Microprocessor Section of this datasheet for
details.
Hardware Mode
EQC[4:0] are used to set the Receiver Gain, Receiver Impedance and the Transmit
Line Build Out. See
Table 23 for more details.
NOTE: Internally pulled “Low” with a 50k
resistor.
RD_DS/EQC1
C7
I
Read Input (Data Strobe)/Equalizer Control Signal 1
Host Mode
This pin is used to communicate a Read or Write operation according to the which
microprocessor is chosen.
See the Microprocessor Section of this datasheet for
details.
Hardware Mode
EQC[4:0] are used to set the Receiver Gain, Receiver Impedance and the Transmit
Line Build Out. See
Table 23 for more details.
NOTE: Internally pulled “Low” with a 50k
resistor.
ALE/EQC2
A7
I
Address Latch Input (Address Strobe)
Host Mode
This pin is used to latch the address contents into the internal registers within the LIU
device. See the Microprocessor Section of this datasheet for details.
Hardware Mode
EQC[4:0] are used to set the Receiver Gain, Receiver Impedance and the Transmit
Line Build Out. See
Table 23 for more details.
NOTE: Internally pulled “Low” with a 50k
resistor.
CS/EQC3
B7
I
Chip Select Input - Host mode:
Host Mode
This pin is used to initiate communication with the microprocessor interface. See the
Microprocessor Section of this datasheet for details.
Hardware Mode
EQC[4:0] are used to set the Receiver Gain, Receiver Impedance and the Transmit
Line Build Out. See
Table 23 for more details.
NOTE: Internally pulled “Low” with a 50k
resistor.
相关PDF资料 |
PDF描述 |
|---|---|
| XRT83VSH314IB-F | IC LIU SH T1/E1/J1 14CH 304TBGA |
| XRT83VSH316IB | IC LIU SH T1/E1/J1 16CH 316STBGA |
| XRT83VSH38IB | IC LIU SH T1/E1/J1 8CH 225BGA |
| XRT85L61IG | IC BITS CLOCK EXTRACTOR 28TSSOP |
| XRT91L30IQ | IC TXRX SONET/SDH 8BIT 64QFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XRT83VSH28IB-F | 功能描述:外围驱动器与原件 - PCI 8 Channel 1.8V-3.3V temp -45 to 85C RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| XRT83VSH28IB-F | 制造商:Exar Corporation 功能描述:T1/E1 LIU IC |
| XRT83VSH314 | 制造商:EXAR 制造商全称:EXAR 功能描述:14-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT |
| XRT83VSH314ES | 功能描述:外围驱动器与原件 - PCI 14 CHT1/E1LIUSH LOW COST VERSION RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| XRT83VSH314IB | 功能描述:接口 - 专用 14 CH, SH T1/E1 1.8V DGTL/3.3V ANLG RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
发布紧急采购，3分钟左右您将得到回复。