- 您现在的位置：买卖IC网 > PDF目录300164 > ZL30402/QCC1 (ZARLINK SEMICONDUCTOR INC) ATM/SONET/SDH SUPPORT CIRCUIT, PQFP80 PDF资料下载
参数资料
| 型号： | ZL30402/QCC1 |
| 厂商： | ZARLINK SEMICONDUCTOR INC |
| 元件分类： | 数字传输电路 |
| 英文描述： | ATM/SONET/SDH SUPPORT CIRCUIT, PQFP80 |
| 封装： | 14 X 14 MM, 1.40 MM HEIGHT, MS-026BEC, LQFP-80 |
| 文件页数： | 25/44页 |
| 文件大小： | 472K |
| 代理商： | ZL30402/QCC1 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
ZL30402
Data Sheet
31
Zarlink Semiconductor Inc.
5.1.4
Reference Switching (RefSel): NORMAL --> HOLDOVER --> NORMAL
The NORMAL to HOLDOVER to NORMAL mode switching is usually performed when:
A reference clock is available but its frequency drifts beyond some specified limit. In a Network Element with
stratum 3 internal clocks, the reference failure is declared when its frequency drifts more than ±12 ppm
beyond its nominal frequency.
During routine maintenance of equipment when orderly switching of reference clocks is possible. This may
happen when synchronization references must be rearranged or when a faulty line card must be replaced.
Figure 10 - Manual Reference Switching
Two types of transitions are possible:
Semi-automatic transition, which involves changing RefSel input to select a secondary reference clock
without changing the mode select inputs MS2, MS1 = 00 (Normal mode). This forces ZL30402 to
momentarily transition through the Holdover state and automatically return to Normal mode after
synchronizing to a secondary reference clock.
Manual transition, which involves switching into Holdover mode (MS2, MS1 = 01), changing references with
RefSel, and manual return to the Normal mode (MS2, MS1 = 00).
In both cases, the change of references provides “hitless” switching.
5.2
Programming Master Clock Oscillator Frequency Calibration Register
The Master Crystal Oscillator and its programmable Master Clock Frequency Calibration register (see Table 18,
Table 19, Table 20, and Table 21) have been described in Section 3.0 "Master Clock Frequency Calibration Circuit",
on page 16. Programming of this register should be done after system has been powered long enough for the
Master Crystal Oscillator to reach a steady operating temperature. When the temperature stabilizes the crystal
oscillator frequency should be measured with an accurate frequency meter. The frequency measurement should be
substituted for the foffset variable in the following equation.
MCFC = 45036 * ( - foffset)
where foffset is the crystal oscillator frequency offset from the nominal 20 000 000 Hz frequency expressed in Hz.
NORMAL
(LOCKED)
00
AUTO
HOLD-
OVER
HOLD-
OVER
01
FREE-
RUN
10
RESET
Ref: OK &
MS2, MS1 == 00
{AUTO}
Ref: OK --> FAIL &
MS2, MS1 == 00
{AUTO}
MS2, MS1 == 01 OR
RefSel change
Ref: FAIL --> OK &
MS2, MS1 == 00 &
AHRD=1 &
MHR= 0-->1 then 1-->0
{MANUAL}
Ref: FAIL --> OK &
MS2, MS1 == 00 &
AHRD=0
{AUTO}
MS2, MS1 == 10 forces
unconditional return from
any state to Free-run
MS2, MS1! = 10
RESET == 1
RefSel Change
相关PDF资料 |
PDF描述 |
|---|---|
| ZL30402/QCG1 | ATM/SONET/SDH SUPPORT CIRCUIT, PQFP80 |
| ZL50112GAG2 | SPECIALTY TELECOM CIRCUIT, PBGA552 |
| ZL50112GAG | SPECIALTY TELECOM CIRCUIT, PBGA552 |
| ZL50114GAG2 | SPECIALTY TELECOM CIRCUIT, PBGA552 |
| ZL50114GAG | SPECIALTY TELECOM CIRCUIT, PBGA552 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ZL30402QCG1 | 制造商:Microsemi Corporation 功能描述:PB FREE SONET / SDH NETWORK ELEMENT PLL - Trays 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC NETWORK PLL SONET/SDH 80LQFP 制造商:Microsemi Corporation 功能描述:IC NETWORK PLL SONET/SDH 80LQFP |
| ZL30406 | 制造商:ZARLINK 制造商全称:Zarlink Semiconductor Inc 功能描述:SONET/SDH Clock Multiplier PLL |
| ZL30406_06 | 制造商:ZARLINK 制造商全称:Zarlink Semiconductor Inc 功能描述:SONET/SDH Clock Multiplier PLL |
| ZL30406QGC | 制造商:Zarlink Semiconductor Inc 功能描述:PLL CLOCK MLTPLR SGL UP TO 19.44MHZ 64TQFP - Trays |
| ZL30406QGC1 | 制造商:ZARLINK 制造商全称:Zarlink Semiconductor Inc 功能描述:SONET/SDH Clock Multiplier PLL |
发布紧急采购，3分钟左右您将得到回复。