- 您现在的位置：买卖IC网 > PDF目录278507 > ZPSD412A0-C-90UI 64K X 8 OTPROM, 40 I/O, PIA-GENERAL PURPOSE, PQFP80 PDF资料下载
参数资料
| 型号： | ZPSD412A0-C-90UI |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 64K X 8 OTPROM, 40 I/O, PIA-GENERAL PURPOSE, PQFP80 |
| 封装： | PLASTIC, TQFP-80 |
| 文件页数： | 98/128页 |
| 文件大小： | 433K |
| 代理商： | ZPSD412A0-C-90UI |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页当前第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页
PSD4XX Family
67
PSD4XX Family
9.5 Power Management Unit
The PSD4XX provides many power saving options. By configuring the PMMRs
(Power Management Mode Registers), the user can reduce power consumption. Table 18
shows the bit configuration of the PMMR0 and PMMR1. The microcontroller is able to
control the power consumption by changing the PMMR bits at run time.
9.5.1 Standby Mode
There are two Standby Modes in the PSD4XX:
t Power Down Mode
t Sleep Mode
9.5.1.1 Power Down Mode
In this mode, the internal devices are shut down except for the I/O ports and the ZPLD.
There are three ways the PSD4XX can enter into the Power Down Mode: by controlling
the CSI input, by activating the Automatic Power Down (APD) Logic and the ZPLD, or when
none of the inputs are changing and the Turbo bit is off.
t The CSI
The CSI input pin is an active low signal. When low, the signal selects and enables the
PSD4XX. The PSD4XX enters into Power Down Mode immediately when the signal
turns high. This signal can be controlled by the microcontrollers, external logic or it can
be grounded. The CSI input turns off the internal bus buffers in Standby Mode. The
address and control signals from the microcontroller are blocked from entering the ZPLD
as inputs.
t The APD Logic
The APD unit enables the user to enter a power down mode independent of controlling
the CSI input. This feature eliminates the need for external logic (decoders and latches)
to power down the PSD. The APD unit concept is based on tracking the activity on the
ALE pin. If the APD unit is enabled and ALE is not active, the 4-bit APD counter starts
counting and will overflow after 15 clocks, generating a PD (Power Down) signal
powering down the PSD. If sleep mode is enabled, then PD signal will also activate the
sleep mode. Immediately after ALE starts pulsing the PSD will get out of the power down
or sleep mode.
The operation of APD is controlled by the PMMR (see Figure 36a). PMMR1 bit 0 selects
the source of the APD counter clock. After reset the APD counter clock is connected to
PE7 (APD CLK) on the PSD. In order to guarantee that the APD will not overflow there
should be less than 15 APD clocks between two ALE pulses. If CLKIN frequency is
adequate, then it can be connected to the APD and PE7 is used for other functions.
The next step is to select the ALE power down polarity. Usually, MCUs entering power
down will freeze their ALE at logic high or low. By programming bit 1 of PMMR0 the
power down polarity can be defined for the APD. If the APD detects that the ALE is in
the power down polarity for 15 APD counter clocks then the PSD will enter a power
down mode. To enable the APD operation, bit 2 in the PMMR0 should be set high.
9.5.1.2 Sleep Mode
The Sleep Mode is activated if the SLEEP EN bit, the APD EN bit, and the ALE Polarity bit
in the PMMR are set, and the APD Counter has overflowed after 15 clocks (see Figure 36).
In Sleep Mode the PSD4XX consumes less power than the Power Down Mode.
In this mode, the ZPLD still monitors the inputs and responds to them. As soon as the ALE
starts pulsing, the PSD4XX exits the Sleep Mode.
The PSD access time from Sleep Mode is specified by tLVDV1. The ZPLD response time to
an input transition is specified by tLVDV2.
The PSD4XX
Architecture
(cont.)
相关PDF资料 |
PDF描述 |
|---|---|
| ZPSD813F1-15J | 1M X 1 FLASH, 27 I/O, PIA-GENERAL PURPOSE, PQCC52 |
| ZPSD813F3V-20J | 1M X 1 FLASH, 27 I/O, PIA-GENERAL PURPOSE, PQCC52 |
| ZDVG10A | 7 SEG NUMERIC DISPLAY, GREEN, 10.16 mm |
| ZMG75W | SINGLE COLOR LED, GREEN, 2.3 mm |
| ZMGUY62M-01 | DUAL COLOR LED |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ZPSD412A1-12J | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Field-Programmable Peripheral |
| ZPSD412A1-12JI | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Field-Programmable Peripheral |
| ZPSD412A1-12LI | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Field-Programmable Peripheral |
| ZPSD412A1-12U | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Field-Programmable Peripheral |
| ZPSD412A1-12UI | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Field-Programmable Peripheral |
发布紧急采购，3分钟左右您将得到回复。