- 您现在的位置：买卖IC网 > PDF目录20617 > 71M6521BE-IGT/F (Maxim Integrated)IC ENERGY METER 8K FLASH 64-LQFP PDF资料下载
参数资料
| 型号： | 71M6521BE-IGT/F |
| 厂商： | Maxim Integrated |
| 文件页数： | 10/97页 |
| 文件大小： | 0K |
| 描述： | IC ENERGY METER 8K FLASH 64-LQFP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 160 |
| 系列： | Single Converter Technology® |
| 测量误差： | 0.4% |
| 电源电压： | 3 V ~ 3.6 V |
| 测量仪表类型： | 单相，双相 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-LQFP |
| 供应商设备封装： | 64-LQFP（10x10） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页
71M6521BE
Energy Meter IC
DATA SHEET
JANUARY 2008
In a typical application, IA and IB are connected to current transformers that sense the current on each phase of the line
voltage. VA is typically connected to a voltage sensor (resistor divider).
The multiplexer control circuit handles the setting of the multiplexer. The function of the multiplexer control circuit is governed
by the I/O RAM registers MUX_ALT, MUX_DIV and EQU. MUX_DIV controls the number of samples per cycle. It can request 2,
3, or 4 multiplexer states per cycle. Multiplexer states above 4 are reserved and must not be used. The multiplexer always
starts at the beginning of its list and proceeds until MUX_DIV states have been converted.
The MUX_ALT bit requests an alternative multiplexer frame. The bit may be asserted on any MPU cycle and may be
subsequently de-asserted on any cycle including the next one. A rising edge on MUX_ALT will cause the multiplexer control
circuit to wait until the next multiplexer cycle and implement a single alternate cycle.
The multiplexer control circuit also controls the FIR filter initiation and the chopping of the ADC reference voltage, VREF. The
multiplexer control circuits clocked by CK32, the 32768Hz clock from the PLL block, and launches each pass through the CE
program.
A/D Converter (ADC)
A single delta-sigma A/D converter digitizes the voltage and current inputs to the 71M6521BE. The resolution of the ADC is
programmable using the FIR_LEN register as shown in the I/O RAM section. ADC resolution can be selected to be 21 bits
( FIR_LEN =0), or 22 bits ( FIR_LEN =1). Conversion time is two cycles of CK32 with FIR_LEN = 0 and three cycles with FIR_LEN
= 1.
In order to provide the maximum resolution, the ADC should be operated with FIR_LEN = 1. Accuracy and timing
specifications in this data sheet are based on FIR_LEN = 1.
Initiation of each ADC conversion is controlled by the multiplexer control circuit as described previously. At the end of each
ADC conversion, the FIR filter output data is stored into the CE DRAM location determined by the multiplexer selection.
FIR Filter
The finite impulse response filter is an integral part of the ADC and it is optimized for use with the multiplexer. The purpose of
the FIR filter is to decimate the ADC output to the desired resolution. At the end of each ADC conversion, the output data is
stored into the fixed CE DRAM location determined by the multiplexer selection. FIR data is stored LSB justified, but shifted left
by nine bits.
Voltage References
The device includes an on-chip precision bandgap voltage reference that incorporates auto-zero techniques. The reference is
trimmed to minimize errors caused by component mismatch and drift. The result is a voltage output with a predictable
temperature coefficient.
The amplifier within the reference is chopper stabilized, i.e. the polarity can be switched by the MPU using the I/O RAM
register CHOP_E (0x2002[5:4]). The two bits in the CHOP_E register enable the MPU to operate the chopper circuit in regular
or inverted operation, or in “toggling” mode. When the chopper circuit is toggled in between multiplexer cycles, DC offsets on
the measured signals will automatically be averaged out.
The general topology of a chopped amplifier is given in Figure 2.
Page: 10 of 97
? 2005-2008 TERIDIAN Semiconductor Corporation
V1.0
相关PDF资料 |
PDF描述 |
|---|---|
| ABC44DRES | CONN EDGECARD 88POS .100 EYELET |
| RS3-4809SZ | CONV DC/DC 3W 20-60VIN 09VOUT |
| VI-BNK-EU-F1 | CONVERTER MOD DC/DC 40V 200W |
| 78M6610+PSU/B00 | IC ENERGY MEASURMENT 1PH 24TQFN |
| ACB65DHLT | CONN EDGECARD 130PS .050 DIP SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 71M6521BE-IGTR/F | 功能描述:计量片上系统 - SoC Residential Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
| 71M6521BE-IGTR/F1 | 功能描述:计量片上系统 - SoC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
| 71M6521DE | 制造商:TERIDIAN 制造商全称:TERIDIAN 功能描述:Energy Meter IC |
| 71M6521DE-DB | 制造商:Maxim Integrated Products 功能描述:Development Boards & Kits - 8051 71M6521DE Demo Brd |
| 71M6521DE-IGT/F | 功能描述:计量片上系统 - SoC Residential Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。