- 您现在的位置：买卖IC网 > PDF目录20617 > 71M6521BE-IGT/F (Maxim Integrated)IC ENERGY METER 8K FLASH 64-LQFP PDF资料下载
参数资料
| 型号： | 71M6521BE-IGT/F |
| 厂商： | Maxim Integrated |
| 文件页数： | 49/97页 |
| 文件大小： | 0K |
| 描述： | IC ENERGY METER 8K FLASH 64-LQFP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 160 |
| 系列： | Single Converter Technology® |
| 测量误差： | 0.4% |
| 电源电压： | 3 V ~ 3.6 V |
| 测量仪表类型： | 单相，双相 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-LQFP |
| 供应商设备封装： | 64-LQFP（10x10） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页当前第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页
71M6521BE
Energy Meter IC
DATA SHEET
JANUARY 2008
CK32
MUX_SYNC
CKTEST
TMUXOUT/RTM
0
1
30
31
0
1
30
31
0
1
30
31
0
1
30
31
FLAG
FLAG
FLAG
FLAG
RTM DATA0 (32 bits)
RTM DATA1 (32 bits)
RTM DATA2 (32 bits)
RTM DATA3 (32 bits)
Figure 17: RTM Output Format
Battery Modes
Shortly after system power (V3P3SYS) is applied, the part will be in MISSION mode. MISSION mode means that the part is
operating with system power and that the internal PLL is stable. This mode is the normal operation mode where the part is
capable of measuring energy.
When system power is not available (i.e. when V1<VBIAS), the 71M6521DE/FE can be in one of three battery modes, i.e.
BROWNOUT, LCD, or SLEEP mode. As soon as V1 falls below VBIAS or when the part wakes up under battery power (with
sufficient voltage margin), the part will automatically enter BROWNOUT mode (see Wake Up Behavior section). From
BROWNOUT mode, the MPU may enter either LCD mode or SLEEP mode by setting either the LCD_ONLY or SLEEP I/O RAM
bits (only one bit can be set at the same time in BROWNOUT mode, since setting one bit will already force the part into SLEEP
or LCD mode, disabling the MPU).
Figure 18 shows a state diagram of the various operation modes, with the possible transitions between modes. For information
on the timing of mode transitions refer to Figure 22 through Figure 24.
When V1 falls below VBIAS or the part wakes up under battery power, the part will automatically enter BROWNOUT mode
(see Wake Up Behavior section). From BROWNOUT mode, the part may choose to enter either LCD mode or SLEEP mode,
as controlled by the MPU via the I/O RAM bits LCD_ONLY and SLEEP .
Meters that do not require functionality in the battery modes still need to contain code that brings the chip from
BROWNOUT mode to SLEEP mode. Otherwise, the chip remains in BROWNOUT mode, once the system power is
missing, and consumes more current than intended.
Similarly, meters equipped with batteries need to contain code that transitions the chip to SLEEP mode as soon as the
battery is attached in production. Otherwise, remaining in BROWNOUT mode would add unnecessary drain to the
battery.
The transition from MISSION mode to BROWNOUT mode is signaled by the IE_PLLFALL interrupt flag (in SFR 0xE8[7]). The
transition in the other direction is signaled by the IE_PLLRISE interrupt flag (SFR 0xE8[6]), when the PLL becomes stable.
Transitions from both LCD and SLEEP mode are initiated by wake-up timer timeout conditions or pushbutton events. When the
PB pin is pulled high (pushbutton is pressed), the IE_PB interrupt flag (SFR 0xE8[4]) is set, and when the wake-up timer times
out, the IE_WAKE interrupt flag (SFR 0xE8[5]) is set.
In the absence of system power, if the voltage margin for the LDO regulator providing 2.5V to the internal circuitry becomes too
low to be safe, the part automatically enters sleep mode (BAT_OK false). The battery voltage must stay above 3V to ensure
that BAT_OK remains true. Under this condition, the 71M6521BE stays in SLEEP mode, even if the voltage margin for the
LDO improves (BAT_OK true).
Table 59 shows the circuit functions available in each operating mode.
V1.0
? 2005-2008 TERIDIAN Semiconductor Corporation
Page: 49 of 97
相关PDF资料 |
PDF描述 |
|---|---|
| ABC44DRES | CONN EDGECARD 88POS .100 EYELET |
| RS3-4809SZ | CONV DC/DC 3W 20-60VIN 09VOUT |
| VI-BNK-EU-F1 | CONVERTER MOD DC/DC 40V 200W |
| 78M6610+PSU/B00 | IC ENERGY MEASURMENT 1PH 24TQFN |
| ACB65DHLT | CONN EDGECARD 130PS .050 DIP SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 71M6521BE-IGTR/F | 功能描述:计量片上系统 - SoC Residential Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
| 71M6521BE-IGTR/F1 | 功能描述:计量片上系统 - SoC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
| 71M6521DE | 制造商:TERIDIAN 制造商全称:TERIDIAN 功能描述:Energy Meter IC |
| 71M6521DE-DB | 制造商:Maxim Integrated Products 功能描述:Development Boards & Kits - 8051 71M6521DE Demo Brd |
| 71M6521DE-IGT/F | 功能描述:计量片上系统 - SoC Residential Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。