- 您现在的位置：买卖IC网 > PDF目录68811 > 71M6533H-IGT/F (TERIDIAN SEMICONDUCTOR CORP) SPECIALTY ANALOG CIRCUIT, PQFP100 PDF资料下载
参数资料
| 型号： | 71M6533H-IGT/F |
| 厂商： | TERIDIAN SEMICONDUCTOR CORP |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 封装： | LEAD FREE, LQFP-100 |
| 文件页数： | 66/124页 |
| 文件大小： | 2008K |
| 代理商： | 71M6533H-IGT/F |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页当前第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页
71M6533/71M6534 Data Sheet
FDS_6533_6534_004
46
2007-2009 TERIDIAN Semiconductor Corporation
v1.1
For each multi-use pin, the corresponding LCD_BITMAP[] register (as described in Section 1.4.7 Digital I/O)
is used to select the pin for DIO or LCD operation. The mapping of the LCD_BITMAP[] registers is speci-
fied in Section 4.1 I/O RAM Map –Functional Order.
LCD segment data is written to the LCD_SEGn[3:0] I/O RAM registers as described in section 4.2 I/O RAM
Description – Alphabetical Order. Note that even though the register names call out bit numbers 3 to 0
some registers use physical bits 4 to 7.
The LCD drivers are grouped into four commons (COM0 – COM3) and up to 56 (71M6533) or 74
(71M6534) segment drivers. The LCD interface is flexible and can drive 7-segment digits, 14- segments
digits or enunciator symbols.
The segment driver SEG18 can be configured to blink at either 0.5 Hz or 1 Hz. The blink rate is con-
trolled by LCD_Y. There can be up to four pixels/segments connected to this driver pin. The I/O RAM
register LCD_BLKMAP18[3:0] identifies which pixels, if any, are to blink.
The LCD bias may be compensated for temperature using the LCD_DAC bits in I/O RAM. The bias may
be adjusted from 1.4 V below the 3.3 V supply (V3P3SYS in mission mode and brownout modes, VBAT
in LCD mode). When the LCD_DAC bits are set to 000, the DAC is bypassed and powered down. This
can be used to reduce current in LCD mode.
1.4.9
Battery Monitor
The battery voltage is measured by the ADC during alternative MUX frames if the BME (Battery Measure
Enable) bit is set. While BME is set, an on-chip 45 k
load resistor is applied to the battery and a scaled
fraction of the battery voltage is applied to the ADC input. After each alternative MUX frame, the result of
the ADC conversion is available at XRAM address 0x07. BME is ignored and assumed zero when system
power is not available.
If VBAT is connected to a drained battery or disconnected, a battery test that sets BME may drain
VBAT’s supply and cause the oscillator to stop. A stopped oscillator may force the device to reset.
Therefore, an unexpected reset during a battery test should be interpreted as a battery failure.
Battery measurement is not very linear but is very reproducible. The best way to perform the calibration
is to set the battery input to the desired failure voltage and then have the MPU firmware record that mea-
surement. After this, the MPU firmware’s battery measurement logic may use the recorded value as the
battery failure limit. The same value can also be a calibration offset for any battery voltage display.
See Section 5.4.5 Battery Monitor for details regarding the ADC LSB size and the conversion accuracy.
1.4.10 EEPROM Interface
The 71M6533 and 71M6534 provides hardware support for either a two-pin or a three-wire (-wire) type
of EEPROM interface. The interfaces use the EECTRL and EEDATA registers for communication.
Two-pin EEPROM Interface
The dedicated 2-pin serial interface communicates with external EEPROM devices. The interface is mul-
tiplexed onto the DIO4 (SCK) and DIO5 (SDA) pins and is selected by setting DIO_EEX = 1. The MPU
communicates with the interface through the SFR registers EEDATA and EECTRL. If the MPU wishes to
write a byte of data to the EEPROM, it places the data in EEDATA and then writes the Transmit code to
EECTRL. This initiates the transmit operation which is finished when the BUSY bit falls. INT5 is also as-
serted when BUSY falls. The MPU can then check the RX_ACK bit to see if the EEPROM acknowledged
the transmission.
A byte is read by writing the Receive command to EECTRL and waiting for the BUSY bit to fall. Upon
completion, the received data is in EEDATA. The serial transmit and receive clock is 78 kHz during each
transmission, and then holds in a high state until the next transmission. The EECTRL bits when the two-
pin interface is selected are shown in Table 41.
相关PDF资料 |
PDF描述 |
|---|---|
| 71M6533-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6542F-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6542G-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6541G-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP64 |
| 71M6541F-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP64 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 71M6533H-IGTR/F | 功能描述:计量片上系统 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
| 71M6533H-IGTR/F1 | 功能描述:计量片上系统 - SoC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
| 71M6533H-IGTR/F2 | 功能描述:计量片上系统 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
| 71M6533-IGT/F | 功能描述:计量片上系统 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
| 71M6533-IGT/F1 | 功能描述:计量片上系统 - SoC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。