参数资料
型号: 71M6533H-IGT/F
厂商: TERIDIAN SEMICONDUCTOR CORP
元件分类: 模拟信号调理
英文描述: SPECIALTY ANALOG CIRCUIT, PQFP100
封装: LEAD FREE, LQFP-100
文件页数: 86/124页
文件大小: 2008K
代理商: 71M6533H-IGT/F
71M6533/71M6534 Data Sheet
FDS_6533_6534_004
64
2007-2009 TERIDIAN Semiconductor Corporation
v1.1
readies the timer to start when the processor writes to the SLEEP or LCD_ONLY registers. The timer is
reset and disarmed whenever the processor is awake. Thus, if it is desired to wake the MPU periodically
(every 5 seconds, for example) the timer must be rearmed every time the part returns from SLEEP or
LCD mode.
2.6
Data Flow
The data flow between the Compute Engine (CE) and the MPU is shown in Figure 28. In a typical appli-
cation, the 32-bit CE sequentially processes the samples from the voltage inputs on pins IA, VA, IB, and
VB, performing calculations to measure active power (Wh), reactive power (VARh), A
2h, and V2h for four-
quadrant metering. These measurements are then accessed by the MPU, processed further and output
using the peripheral devices available to the MPU. Figure 28 illustrates the CE/MPU data flow.
Figure 28: MPU/CE Data Flow
2.7
CE/MPU Communication
Figure 29 shows the functional relationships between the CE and the MPU. The CE is controlled by the
MPU via shared registers in the I/O RAM and in RAM.
The CE outputs two interrupt signals to the MPU: CE_BUSY and XFER_BUSY, which are connected to
the MPU interrupt service inputs as external interrupts. CE_BUSY indicates that the CE is actively pro-
cessing data. This signal will occur once every multiplexer cycle. XFER_BUSY indicates that the CE is
updating data to the output region of the RAM. This will occur whenever the CE has finished generating a
sum by completing an accumulation interval determined by SUM_CYCLES * PRE_SAMPS samples. Inter-
rupts to the MPU occur on the falling edges of the XFER_BUSY and CE_BUSY signals.
Refer to Section 4.3 CE Interface Description for additional information on setting up the device using the
MPU firmware.
VARSUM
WSUM
APULSEW
APULSER
EXT PULSE
SAG CONTROL
DATA
DIO
XFER BUSY
SAMPLES
CE
MPU
INTERRUPTS
I/O RAM (Configuration RAM)
Mux Control
ADC
DISPLAY (Memory
mapped LCD
segments)
SERIAL
(UART0/1)
EEPROM
(I
2C)
VAR
(DIO7)
PULSES
W (DIO6)
CE BUSY
Figure 29: MPU/CE Communication
CE
MPU
Pre-
Processor
Post-
Processor
IRQ
Processed
Metering
Data
Pulses
I/O RAM (Configuration RAM)
Samples
Data
相关PDF资料
PDF描述
71M6533-IGT/F SPECIALTY ANALOG CIRCUIT, PQFP100
71M6542F-IGT/F SPECIALTY ANALOG CIRCUIT, PQFP100
71M6542G-IGTR/F SPECIALTY ANALOG CIRCUIT, PQFP100
71M6541G-IGTR/F SPECIALTY ANALOG CIRCUIT, PQFP64
71M6541F-IGTR/F SPECIALTY ANALOG CIRCUIT, PQFP64
相关代理商/技术参数
参数描述
71M6533H-IGTR/F 功能描述:计量片上系统 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6533H-IGTR/F1 功能描述:计量片上系统 - SoC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6533H-IGTR/F2 功能描述:计量片上系统 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6533-IGT/F 功能描述:计量片上系统 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6533-IGT/F1 功能描述:计量片上系统 - SoC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel