参数资料
型号: 71M6533H-IGT/F
厂商: TERIDIAN SEMICONDUCTOR CORP
元件分类: 模拟信号调理
英文描述: SPECIALTY ANALOG CIRCUIT, PQFP100
封装: LEAD FREE, LQFP-100
文件页数: 95/124页
文件大小: 2008K
代理商: 71M6533H-IGT/F
71M6533/71M6534 Data Sheet
FDS_6533_6534_004
72
2007-2009 TERIDIAN Semiconductor Corporation
v1.1
Figure 40: External Components for the Emulator Interface
3.14 Connecting a Battery
It is important that a valid voltage is connected to the VBAT pin at all times. For meters without a battery,
VBAT should be connected directly to V3P3SYS. Designs for meters with batteries need to ensure that
the meter functions even when the battery voltage decreases below the specified voltage for VBAT. This
can be achieved by connecting a diode from V3P3SYS to VBAT. However, the battery test will yield in-
accurate results if that technique is used, since the voltage at V3P3SYS will feed current to the VBAT pin.
A better solution is shown in Figure 41: During the battery test, a DIO pin is activated as an output and
applies a low voltage to the anode of the diode. This prevents the voltage at the power supply to influence
the voltage at the VBAT pin.
Figure 41: Connecting a Battery
Meters equipped with batteries need to contain code that transitions the chip to SLEEP mode as
soon as the battery is attached in production. Otherwise, remaining in BROWNOUT mode would
add unnecessary drain to the battery.
3.15 Flash Programming
Operational or test code can be programmed into the flash memory using either an in-circuit emulator or
the Flash Programmer Module (TFP-2) available from Teridian. The flash programming procedure uses
the E_RST, E_RXTX, and E_TCLK pins. The FL_BANK register has to be set to the value corresponding
to the bank that is being programmed.
71M6533/6534
V3P3A
DIO
Power
Supply
V3P3SYS
VBAT
Battery or
Super-Cap
+
-
E_RST
71M6533/71M6534
E_TCLK
62
Ω
62
62
22 pF
LCD Segments
ICE_E
V3P3D
E_RXT
(optional)
相关PDF资料
PDF描述
71M6533-IGT/F SPECIALTY ANALOG CIRCUIT, PQFP100
71M6542F-IGT/F SPECIALTY ANALOG CIRCUIT, PQFP100
71M6542G-IGTR/F SPECIALTY ANALOG CIRCUIT, PQFP100
71M6541G-IGTR/F SPECIALTY ANALOG CIRCUIT, PQFP64
71M6541F-IGTR/F SPECIALTY ANALOG CIRCUIT, PQFP64
相关代理商/技术参数
参数描述
71M6533H-IGTR/F 功能描述:计量片上系统 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6533H-IGTR/F1 功能描述:计量片上系统 - SoC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6533H-IGTR/F2 功能描述:计量片上系统 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6533-IGT/F 功能描述:计量片上系统 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6533-IGT/F1 功能描述:计量片上系统 - SoC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel