参数资料
型号: 71M6533H-IGT/F
厂商: TERIDIAN SEMICONDUCTOR CORP
元件分类: 模拟信号调理
英文描述: SPECIALTY ANALOG CIRCUIT, PQFP100
封装: LEAD FREE, LQFP-100
文件页数: 84/124页
文件大小: 2008K
代理商: 71M6533H-IGT/F
71M6533/71M6534 Data Sheet
FDS_6533_6534_004
62
2007-2009 TERIDIAN Semiconductor Corporation
v1.1
Figure 26: Power-Up Timing with VBAT only
2.4
Fault and Reset Behavior
2.4.1
Reset Mode
When the RESET pin is pulled high, all digital activity stops. The oscillator and RTC module continue to
run. Additionally, all I/O RAM bits are set to their default states. As long as V1, the input voltage at the
power fault block, is greater than VBIAS, the internal 2.5 V regulator will continue to provide power to the
digital section.
Once initiated, the reset mode will persist until the reset timer times out, signified by WAKE rising. This
will occur in 4100 cycles of the real time clock after RESET goes low, at which time the MPU will begin
executing its pre-boot and boot sequences from address 00. See the description of Program Security
in Section 1.4.5 for additional descriptions of pre-boot and boot.
If system power is not present, the reset timer duration will be 2 cycles of the crystal clock at which time
the MPU will begin executing in BROWNOUT mode, starting at address 00.
2.4.2
Power Fault Circuit
The 71M6533 and 71M6534 includes a comparator to monitor system power fault conditions. When the
output of the comparator falls (V1<VBIAS), the I/O RAM bits PLL_OK are zeroed and the part switches to
BROWNOUT mode if a battery is present. Once system power returns, the MPU remains in reset and
does not transition to MISSION mode until 2048 to 4096 CK32 clock cycles later, when PLL_OK rises. If
a battery is not present, as indicated by BAT_OK=0, WAKE will fall and the part will enter SLEEP mode.
There are several conditions the device could be in as system power returns. If the part is in
BROWNOUT mode, it will automatically switch to MISSION mode when PLL_OK rises. It will receive an
interrupt indicating this. No configuration bits will be reset or reconfigured during this transition.
If the part is in LCD or SLEEP mode when system power returns, it will also switch to MISSION mode
when PLL_OK rises. In this case, all configuration bits will be in the reset state due to WAKE having
been zero. The RTC clock will not be disturbed, but the MPU RAM must be re-initialized. The hardware
watchdog timer will become active when the part enters MISSION mode.
time
VBAT
MPU Mode
Battery
Current
MPU Clock
Source
Xtal
PLL_OK
WAKE
Internal
RESETZ
1024 CK32
cycles
BROWNOUT
14.5 CK32
cycles
VBAT_OK
相关PDF资料
PDF描述
71M6533-IGT/F SPECIALTY ANALOG CIRCUIT, PQFP100
71M6542F-IGT/F SPECIALTY ANALOG CIRCUIT, PQFP100
71M6542G-IGTR/F SPECIALTY ANALOG CIRCUIT, PQFP100
71M6541G-IGTR/F SPECIALTY ANALOG CIRCUIT, PQFP64
71M6541F-IGTR/F SPECIALTY ANALOG CIRCUIT, PQFP64
相关代理商/技术参数
参数描述
71M6533H-IGTR/F 功能描述:计量片上系统 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6533H-IGTR/F1 功能描述:计量片上系统 - SoC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6533H-IGTR/F2 功能描述:计量片上系统 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6533-IGT/F 功能描述:计量片上系统 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6533-IGT/F1 功能描述:计量片上系统 - SoC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel