参数资料
型号: 71M6543F-IGTR/F
厂商: Maxim Integrated
文件页数: 63/154页
文件大小: 0K
描述: IC ENERGY METER 64K FLSH 100LQFP
标准包装: 1,000
系列: *
71M6543F/71M6543G Data Sheet
Table 52: LCD Configurations
Name
LCD_ALLCOM
LCD_BAT
LCD_E
LCD_ON
LCD_BLANK
LCD_RST
LCD_DAC[4:0]
LCD_CLK[1:0]
Location
2400[3]
2402[7]
2400[7]
240C[0]
240C[1]
240C[2]
240D[4:0]
2400[1:0]
Rst
0
0
0
0
0
0
0
0
Wk
Dir
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Description
Configures all 6 SEG/COM pins as COM. Has no effect
on pins whose LCD_MAP bit is zero.
Connects the LCD power supply to VBAT in all modes.
Enables the LCD display. When disabled, VLC2,
VLC1, and VLC0 are ground as are the COM and SEG
outputs if their LCD_MAP bit is 1.
LCD_ON = 1 turns on all LCD segments without
affecting the LCD data. Similarly, LCD_BLANK = 1
turns off all LCD segments without affecting the LCD
data. If both bits are set, all LCD segments are turned
on.
Clear all bits of LCD data. These bits affect SEGDIO
pins that are configured as LCD drivers.
This register controls the LCD contrast DAC which
adjusts the VLCD voltage and has an output range of
2.65 VDC to 5.3 VDC. The VLCD voltage is
VLCD = 2.65 + 2.65 * LCD_DAC[4:0] /31
Thus, the LSB of the DAC is 85.5 mV. The maximum
DAC output voltage is limited by V3P3SYS, VBAT, and
whether LCD_BSTE is set.
Sets the LCD clock frequency (1/T). See definition of T
in Figure17.      Note: fw=32768Hz
00-fw/2^9, 01-fw/2^8, 10-fw/2^7, 11-fw/2^6
The LCD bias and multiplex mode.
LCD_MODE[2:0] 2400[6:4]
0
R/W
LCD_MODE
000
001
010
011
100
101
110
Output
4 states, 1/3 bias
3 states, 1/3 bias
2 states, ? bias
3 states, ? bias
Static display
5 states, 1/3 bias
6 states, 1/3 bias
This register specifies how VLCD is generated.
LCD_VMODE[1:0] 2401[7:6]
00
00
R/W
LCD_VMODE
11
10
01
00
Description
External VLCD
LCD boost and LCD DAC
enabled
LCD DAC enabled
No boost and no DAC.
VLCD = VBAT or V3P3SYS
The LCD can be driven in static, ? bias, and 1/3 bias modes. Figure 17 defines the COM waveforms.
Note that COM pins that are not required in a specific mode maintain a segment off state rather than
GND, VCC, or high impedance.
The segment drivers SEGDIO22 and SEGDIO23 can be configured to blink at either 0.5 Hz or 1 Hz.
The blink rate is controlled by LCD_Y (I/O RAM 0x2400[2]) . There can be up to six pixels/segments
connected to each of these driver pins. The I/O RAM fields LCD_BLKMAP22[5:0] (I/O RAM 0x2402[5:0])
and LCD_BLKMAP23[5:0] (I/O RAM 0x2401[5:0]) identify which pixels, if any, are to blink.
LCD_BLKMAP22[5:0] and LCD_BLKMAP23[5:0] are non-volatile.
v2
63
相关PDF资料
PDF描述
R1S-0524/HP CONV DC/DC 1W 05VIN 24VOUT
SS10P3CL-M3/87A DIODE SCHOTTKY 10A 30V SMPC
ISL6549CRZ IC REG DL BCK/LINEAR SYNC 16-QFN
ISL6549IRZ-T IC REG DL BCK/LINEAR SYNC 16-QFN
AMC40DRTF CONN EDGECARD 80POS .100 DIP SLD
相关代理商/技术参数
参数描述
71M6543FT-IGT/F 制造商:Maxim Integrated Products 功能描述:ENERGY METER ICS - Rail/Tube
71M6543FT-IGTR/F 制造商:Maxim Integrated Products 功能描述:3-PHASE SOC, 64KB FLASH, PRES TEMP SENSOR - Tape and Reel
71M6543G 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Selectable Gain of 1 or 8 for One Current Energy Meter ICs Metrology Compensation
71M6543GH 制造商:未知厂家 制造商全称:未知厂家 功能描述:电表IC
71M6543GHT-IGT/F 制造商:Maxim Integrated Products 功能描述:3-PHASE, 128KB, PRES TEMP SENSOR, HI PREC - Bulk