- 您现在的位置：买卖IC网 > PDF目录20606 > 71M6543F-IGTR/F (Maxim Integrated)IC ENERGY METER 64K FLSH 100LQFP PDF资料下载
参数资料
| 型号： | 71M6543F-IGTR/F |
| 厂商： | Maxim Integrated |
| 文件页数： | 77/154页 |
| 文件大小： | 0K |
| 描述： | IC ENERGY METER 64K FLSH 100LQFP |
| 标准包装： | 1,000 |
| 系列： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页当前第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页
71M6543F/71M6543G Data Sheet
3.2.1
BRN Mode
In BRN mode, most non-metering digital functions are active (as shown in Table 61 ) including ICE, UART,
EEPROM, LCD and RTC. In BRN mode, the PLL continues to function at the same frequency as MSN
mode. It is up to the MPU to scale down the PLL (using PLL_FAST, I/O RAM 0x2200[4] ) or the MPU
frequency (using MPU_DIV[2:0], I/O RAM 0x2200[2:0] ) in order to save power.
From BRN mode, the MPU can choose to enter LCD or SLP modes. When system power is restored
while the 71M6543 is in BRN mode, the part automatically transitions to MSN mode.
The recommended minimum power configuration for BRN mode is as follows:
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
RCE0 = 0x00 ( I/O RAM 0x2709[7:0] ) - remote sensors disabled
LCD_BAT = 1 ( I/O RAM 0x2402[7] ) - LCD powered from VBAT
LCD_VMODE[1:0] = 0 ( I/O RAM 0x2401[7:6] ) - 5V LCD boost disabled
CE6 = 0x00 ( I/O RAM 0x2106 ) - CE, RTM and CHOP are disabled
MUX_DIV[3:0] = 0( I/O RAM 0x2100[7:4]) - the ADC multiplexer is disabled
ADC_E = 0 ( I/O RAM 0x2704[4] ) - ADC disabled
VREF_CAL = 0 ( I/O RAM 0x2704[7] ) – Vref not driven out
VREF_DIS = 1 ( I/O RAM 0x2704[6] ) - Vref disabled
PRE_E = 0 ( I/O RAM 0x2704[5] - pre-amp disabled
BCURR = 0 ( I/O RAM 0x2704[3] ) - battery 100μA current load OFF
TMUX[5:0] = 0x0E ( I/O RAM 0x2502[5:0] ) – TMUXOUT output set to a dc value
TMUX2[4:0] = 0x0E ( I/O RAM 0x2503[4:0] ) – TMUXOUT2 output set to a dc value
CKGN = 0x24 ( I/O RAM 0x2200 ) - PLL set slow, and MPU_DIV[2:0] (I/O RAM 0x2200[2:0] ) set to maximum
TEMP_PER[2:0] = 6 ( I/O RAM 0x28A0[2:0] ) - temp measurement set to automatic every 512 s
TEMP_BSEL = 1 ( I/O RAM 0x28A0[7] ) - temperature sensor monitors VBAT
PCON | = 1 ( SFR 0x87 ) - at the end of the main BRN loop, halt the MPU and wait for an interrupt
The baud rate registers are adjusted as needed
All unused interrupts are disabled
3.2.2
LCD Mode
LCD mode may be commanded by the MPU at any time by setting the LCD_ONLY control bit ( I/O RAM
0x28B2[6] ). However, it is recommended that the LCD_ONLY control bit be set by the MPU only after the
71M6543 has entered BRN mode. For example, if the 71M6543 is in MSN mode when LCD_ONLY is set,
the duration of LCD mode is very brief and the 71M6543 immediately 'wakes'.
In LCD mode, V3P3D is disabled, and the VBAT pin supplies the LCD current. Before asserting
LCD_ONLY mode, it is recommended that the MPU minimize PLL current by reducing the output
frequency of the PLL to 6.29 MHz (i.e., write PLL_FAST = 0, I/O RAM 0x2200[4] ). The LCD boost system
requires a clock from the PLL for its operation. Thus, if the LCD boost system is enabled (i.e.,
LCD_VMODE[1:0] = 10, I/O RAM 0x2401[7:6] ), then the PLL is automatically kept active during LCD
mode, otherwise the PLL is de-activated.
In LCD mode, the data contained in the LCD_SEG registers is displayed using the segment driver pins.
Up to two LCD segments connected to the pins SEGDIO22 and SEGDIO23 can be made to blink without
the involvement of the MPU, which is disabled in LCD mode. To minimize battery power consumption,
only segments that are used should be enabled.
After the transition from LCD mode to MSN or BRN mode, the PC (Program Counter) is at 0x0000, the
XRAM is in an undefined state, and configuration I/O RAM bits are reset (see Table 70 for I/O RAM state
upon wake). The data stored in non-volatile I/O RAM locations is preserved in LCD mode (the shaded
locations in Table 70 are non-volatile).
v2
77
相关PDF资料 |
PDF描述 |
|---|---|
| R1S-0524/HP | CONV DC/DC 1W 05VIN 24VOUT |
| SS10P3CL-M3/87A | DIODE SCHOTTKY 10A 30V SMPC |
| ISL6549CRZ | IC REG DL BCK/LINEAR SYNC 16-QFN |
| ISL6549IRZ-T | IC REG DL BCK/LINEAR SYNC 16-QFN |
| AMC40DRTF | CONN EDGECARD 80POS .100 DIP SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 71M6543FT-IGT/F | 制造商:Maxim Integrated Products 功能描述:ENERGY METER ICS - Rail/Tube |
| 71M6543FT-IGTR/F | 制造商:Maxim Integrated Products 功能描述:3-PHASE SOC, 64KB FLASH, PRES TEMP SENSOR - Tape and Reel |
| 71M6543G | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Selectable Gain of 1 or 8 for One Current Energy Meter ICs Metrology Compensation |
| 71M6543GH | 制造商:未知厂家 制造商全称:未知厂家 功能描述:电表IC |
| 71M6543GHT-IGT/F | 制造商:Maxim Integrated Products 功能描述:3-PHASE, 128KB, PRES TEMP SENSOR, HI PREC - Bulk |
发布紧急采购，3分钟左右您将得到回复。