- 您现在的位置：买卖IC网 > PDF目录16270 > 73S1217F-EB-LITE (Maxim Integrated Products)BOARD EVAL 73S1217F CBL/DOC/CD PDF资料下载
参数资料
| 型号： | 73S1217F-EB-LITE |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 80/93页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL 73S1217F CBL/DOC/CD |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 系列： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页当前第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页
UG_12xxF_016
73S12xxF Software User Guide
Rev. 1.50
81
punIccTSTimeOut: Input/output parameter
Specifies the maximum delay in clock cycles between the de-assertion of the RST
signal and the leading edge of the TS character of the ATR. [Default value is 40 000]
pucIccRxErrorCounterT0: Input/output parameter
Specifies the maximum number of errors allowed when the Interface Device is in
reception mode in T=0 protocol.
pucIccTxErrorCounterT0: Input/output parameter
Specifies the maximum number of errors when the Interface Device is in
transmission mode in T=0 protocol.
pucIccTxErrorCounterT1: Input/output parameter
Specifies the maximum number of errors when T=1. The most significant nibble
gives the maximum number of R(NA) block transmissions, while the least significant
nibble gives the maximum number of I or S-block retransmissions.
ucIccConfigurationByte: Input/output parameter
This byte contains the following configuration bits:
[b0]
bIccIFSDRequestT1: Input/output. Specifies if the next I-Block will be
preceded by an S(IFS request) (TRUE) or not (FALSE).
[b1]
bIccDeactivatedOnTimeOutErrorT1: Input/output. Specifies if the Smart Card
interface is to be de-activated (TRUE) on a TimeOut error. Otherwise, an error
recovery procedure is engaged.
[b2]
bIccNADErrorCheckingT1: Input/output. Specifies whether the NAD errors
are to be checked (TRUE) or not (FALSE).
[b3]
bIccABORTManagementT1: Input/output. Specifies whether the ABORT
Request is to be managed (TRUE) or if the contacts are to be de-activated on
S(ABORT Request) reception (FALSE).
[b4]
bIccRESYNCHManagementT1: Input/output. Specifies whether an
S(RESYNCH Request) command is to be sent when too many errors occur
(TRUE) or if a de-activation sequence is to be initiated (FALSE).
[b5]
bIccRetransmitLastBlockAfterRESYNCHT1: Input/output. Specifies whether
the last block in T=1 protocol is to be retransmitted after a resynchronization
occurs or the whole command. [Useful for Microsoft IFDTESTs suite]
[b6]
bIccWarningStatusBytesManagementT0: Input/output. Specifies if the IFD
must inform the application level of whether the status bytes have been
received just after the command header transmission or after the command
data transmission (in T=0 protocol). [Useful for EMV Test suites]
[b7]
bIccDeactivateOnIFSDNegotiationError: Input/output. Specifies if the Smart
Card interface is to be de-activated on an IFSD negotiation error.
Icc_Hz: Input parameter
Specifies the desired Smart Card clock frequency. Available values are defined in
the API_Struct_12.h file (LAPI). The default value for both the internal and external
slots is 3.69 MHz.
Care must be taken to make sure the Smart Card Clock is slower than the CPU clock. Since the
CPU has much more overhead to process, a faster Smart Card clock may out run the CPU
resulting in unexpected or undesirable delays.
Since the Smart Card Clock for the external slots (slot ICC_2
ND or higher) is driven by the 73S12xxF
single source, all external slots will share the same SC clock configuration. For example, if an application
sets the first external slot to one rate, subsequent calls to this function with a different rate will be ignored.
DebouncePUEnable: Input parameter
The higher order (most significant) nibble of this byte enables (SC_DEBOUNCEON)
or disables (SC_DEBOUNCEOFF) card debounce. The low order (least significant)
nibble of this byte enables (TRUE) or disables (FALSE) the Pull-Up.
相关PDF资料 |
PDF描述 |
|---|---|
| UPT2D221MHD6 | CAP ALUM 220UF 200V 20% RADIAL |
| MAX5391NEVMINIQU+ | EVAL KIT MAX5391 |
| GSC08DRTN-S93 | CONN EDGECARD 16POS DIP .100 SLD |
| CM453232-R56KL | INDUCTOR 560NH 520MA SMD |
| REC15-1212D/H3 | CONV DC/DC 15W 12VIN +/-12VOUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 73S1217F-IMR/F | 制造商:TERIDIAN 制造商全称:TERIDIAN 功能描述:Bus-Powered 80515 System-on-Chip with USB, ISO 7816 / EMV, PINpad and More |
| 73S13B | 制造商:QUARTZCOM 制造商全称:QUARTZCOM the communications company 功能描述:-20 ~ +70 °C commercia l application -30 ~ +75 °C on request |
| 73S5040G01X0A | 制造商:NEX Computers 功能描述:INTEL 40GB SSD - Bulk |
| 73S8009C | 制造商:TERIDIAN 制造商全称:TERIDIAN 功能描述:Versatile Power Management and Smart Card Interface IC |
| 73S8009C-20IM/F | 功能描述:输入/输出控制器接口集成电路 Smart Card Interface IC RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。