- 您现在的位置：买卖IC网 > PDF目录16577 > 73S8009R-IM/F (Maxim Integrated Products)IC SMART CARD LEVEL SHIFT 20-QFN PDF资料下载
参数资料
| 型号： | 73S8009R-IM/F |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 14/23页 |
| 文件大小： | 0K |
| 描述： | IC SMART CARD LEVEL SHIFT 20-QFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 490 |
| 应用： | 智能卡读取器，写入器 |
| 电源电压： | 2.7 V ~ 3.6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-VFQFN 裸露焊盘 |
| 供应商设备封装： | 20-QFN（4x4） |
| 包装： | 管件 |
73S8009R Data Sheet
DS_8009R_056
3.2
System Controller Interface
Four separate digital inputs allow direct control of the card interface from the host as follows:
?
?
?
Pin CS: Enables the system controller interface.
Pin CMDVCC# and/or CMDVCC% : When low, starts an activation sequence.
Pin RSTIN: Controls the card Reset signal (when enabled by the sequencer).
Other functions are controlled as follows:
?
?
?
?
3.3
PWRDN places the 73S8009R in a low power mode and shuts down all functions.
The card clock is completely controlled by CLKIN.
Vcc output voltage valid is indicated on the RDY pin.
Interrupt output to the host: As long as the card is not activated, the OFF pin informs the host about
the card presence only (low = no card in the reader).
When CMDVCC is set low (Card activation sequence requested from the host), a low level on OFF
means a fault has been detected (e.g. card removal during card session, or voltage fault, or thermal /
over-current fault). This condition automatically initiates a deactivation sequence.
Power Supply and Voltage Supervision
The Teridian 73S8009R smart card interface IC incorporates a LDO voltage regulator. The voltage
output is controlled by the digital input sequence on CMDVCC# and CMDVCC% . This regulator is able to
provide either 1.8 V, 3 V or 5 V card voltages from the power supply applied on the VPC pin.
Digital circuitry is powered by the power supply applied on the VDD pin. V DD also defines the voltage
range to interface with the system controller.
Three voltage supervisors constantly check the presence of the voltages V DD , V PC and V CC . A card
deactivation sequence is forced upon a fault detected by any of these voltage supervisors.
The voltage regulator can provide a card current of 65 mA in compliance with EMV 4.1, and of at least
90 mA in compliance with ISO7816-3. The V CC voltage supervisor threshold values are defined from the
EMV standard.
3.4
Card Power Supply
The card power supply is internally provided by the LDO regulator. The signals CMDVCC# and
CMDVCC% control the turn-on, output voltage value, and turn-off of V CC . When either signal is asserted
low, V CC will ramp to the selected value or if both signals are asserted low (within 400 ns of each other),
V CC will ramp to 1.8 volts. These signals are edge triggered. If CMDVCC% is asserted low (to command
V CC to be 5 V) and at a much later time (greater than 2 μs, typically), CMDVCC# is asserted low, it will be
ignored (and vice versa).
At the assertion (low) of either or both CMDVCC#/CMDVCC% signals , V CC will rise to the requested value.
When V CC rises to an acceptable value, and stays above that value for approximately 20 μs, RDY will be
set high. Approximately 510 μs after the fall of CMDVCC#/CMDVCC% the circuit will check the see if V CC
is at or above the required minimum value (indicated by RDY=1) and if not, will begin an emergency
deactivation sequence. During the 510 μs time, over-temperature, card removal, or de-assertion of
CMDVCC#/CMDVCC% shall also initiate an emergency deactivation sequence.
14
Rev. 1.3
相关PDF资料 |
PDF描述 |
|---|---|
| EEM15DRMN-S664 | CONN EDGECARD 30POS .156 WW |
| GCM08DTMT | CONN EDGECARD 16POS R/A .156 SLD |
| EEM15DRMD-S664 | CONN EDGECARD 30POS .156 WW |
| RBA15DTKT-S288 | CONN EDGECARD 30POS .125 EXTEND |
| GCM15DCBI | CONN EDGECARD 30POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 73S8009R-IMR/F | 功能描述:输入/输出控制器接口集成电路 Smart Card Interface IC RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
| 73S8010C | 制造商:TERIDIAN 制造商全称:TERIDIAN 功能描述:Smart Card Interface |
| 73S8010C-DB | 功能描述:界面开发工具 73S8010C Demo Brd RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| 73S8010C-IL/F | 功能描述:I2C 接口集成电路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:NXP Semiconductors 电源电压-最大:5.5 V 电源电压-最小:2.3 V 最大工作频率:400 KHz 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-16 |
| 73S8010C-ILR/F | 功能描述:I2C 接口集成电路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:NXP Semiconductors 电源电压-最大:5.5 V 电源电压-最小:2.3 V 最大工作频率:400 KHz 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-16 |
发布紧急采购，3分钟左右您将得到回复。