- 您现在的位置：买卖IC网 > PDF目录369345 > 7782 (意法半导体) 32 Mbit (2Mb x 16, Dual Bank, Burst ) 1.8V Supply Flash Memory PDF资料下载
参数资料
| 型号： | 7782 |
| 厂商： | 意法半导体 |
| 英文描述： | 32 Mbit (2Mb x 16, Dual Bank, Burst ) 1.8V Supply Flash Memory |
| 中文描述： | 32兆位（含2Mb × 16，双行，突发）1.8V电源快闪记忆体 |
| 文件页数： | 22/63页 |
| 文件大小： | 435K |
| 代理商： | 7782 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页
M58CR032C, M58CR032D
22/63
Protection Register Program Command
The Protection Register Program command is
used to Program the 64 bit user One-Time-Pro-
grammable (OTP) segment of the Protection Reg-
ister. The segment is programmed 16 bits at a
time. When shipped all bits in the segment are set
to ‘1’. The user can only program the bits to ‘0’.
Two write cycles are required to issue the Protec-
tion Register Program command.
I
The first bus cycle sets up the Protection
Register Program command.
I
The second latches the Address and the Data to
be written to the Protection Register and starts
the Program/Erase Controller.
Read operations output the Status Register con-
tent after the programming has started.
The segment can be protected by programming bit
1 of the Protection Lock Register. Bit 1 of the Pro-
tection Lock Register protects bit 2 of the Protec-
tion Lock Register. Programming bit 2 of the
Protection Lock Register will result in a permanent
protection of the Security Block (see Figure 5, Se-
curity Block and Protection Register Memory
Map). Attempting to program a previously protect-
ed Protection Register will result in a Status Reg-
ister error. The protection of the Protection
Register and/or the Security Block is not revers-
ible.
The Protection Register Program cannot be sus-
pended. See Appendix B, Figure 25, Protection
Register Program Flowchart and Pseudo Code,
for a flowchart for using the Protection Register
Program command.
Block Lock Command
The Block Lock command is used to lock a block
and prevent Program or Erase operations from
changing the data in it. All blocks are locked at
power-up or reset.
Two Bus Write cycles are required to issue the
Block Lock command.
I
The first bus cycle sets up the Block Lock
command.
I
The second Bus Write cycle latches the block
address.
The lock status can be monitored for each block
using the Read Electronic Signature command.
Table. 14 shows the Lock Status after issuing a
Block Lock command.
The Block Lock bits are volatile, once set they re-
main set until a hardware reset or power-down/
power-up. They are cleared by a Blocks Unlock
command. Refer to the section, Block Locking, for
a detailed explanation. See Appendix B, Figure
24, Locking Operations Flowchart and Pseudo
Code, for a flowchart for using the Lock command.
Block Unlock Command
The Blocks Unlock command is used to unlock a
block, allowing the block to be programmed or
erased. Two Bus Write cycles are required to is-
sue the Blocks Unlock command.
I
The first bus cycle sets up the Block Unlock
command.
I
The second Bus Write cycle latches the block
address.
The lock status can be monitored for each block
using the Read Electronic Signature command.
Table. 13 shows the protection status after issuing
a Block Unlock command. Refer to the section,
Block Locking, for a detailed explanation and Ap-
pendix B, Figure 24, Locking Operations Flow-
chart and Pseudo Code, for a flowchart for using
the Unlock command.
Block Lock-Down Command
A locked block cannot be Programmed or Erased,
or have its protection status changed when WP is
low, V
IL
. When WP is high, V
IH,
the Lock-Down
function is disabled and the locked blocks can be
individually unlocked by the Block Unlock com-
mand.
Two Bus Write cycles are required to issue the
Block Lock-Down command.
I
The first bus cycle sets up the Block Lock
command.
I
The second Bus Write cycle latches the block
address.
The lock status can be monitored for each block
using the Read Electronic Signature command.
Locked-Down blocks revert to the locked (and not
locked-down) state when the device is reset on
power-down. Table. 14 shows the Lock Status af-
ter issuing a Block Lock-Down command. Refer to
the section, Block Locking, for a detailed explana-
tion and Appendix B, Figure 24, Locking Opera-
tions Flowchart and Pseudo Code, for a flowchart
for using the Lock-Down command.
Set Burst Configuration Register Command.
The Set Burst Configuration Register command is
used to write a new value to the Burst Configura-
tion Control Register which defines the burst
length, type, X latency, Synchronous/Asynchro-
nous Read mode and the valid Clock edge config-
uration.
Two Bus Write cycles are required to issue the Set
Burst Configuration Register command. The first
cycle writes the setup command and the address
corresponding to the Set Burst Configuration Reg-
ister content. The second cycle writes the Burst
Configuration Register data and the confirm com-
mand. Once the command is issued the memory
returns to Read mode as if a Read Memory Array
command had been issued.
相关PDF资料 |
PDF描述 |
|---|---|
| 7801-301XC | HIGH SPEED, BUFFER AMPLIFIER AMP |
| 78042FG | 1 watt dc-dc converters |
| 78044F | Common to 78K/0 Series |
| 780058 | Common to 78K/0 Series |
| 780058Y | Common to 78K/0 Series |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 778200-01 | 制造商:NI 制造商全称:National Instruments Corporation 功能描述:4-Channel Monochrome Image Acquisition |
| 778201-01 | 制造商:NI 制造商全称:National Instruments Corporation 功能描述:Real-Time Embedded Controllers for PXI |
| 778204-01 | 制造商:NI 制造商全称:National Instruments Corporation 功能描述:S Series Multifunction DAQ 12 or 16-Bit,1 to 10 MS/s, 4 Analog Inputs |
| 778218-000 | 制造商:TE Connectivity 功能描述:WALLBOX KIT LAN OUTLET WHITE |
| 77-82500 | 功能描述:D-Sub微型D连接器 50P R/A SOCKET HIGH/STD HOOD RoHS:否 制造商:3M Electronic Solutions Division 位置/触点数量:26 排数:2 安装风格:SMD/SMT 安装角:Right 端接类型:Solder 型式:Female |
发布紧急采购，3分钟左右您将得到回复。