- 您现在的位置：买卖IC网 > PDF目录369345 > 7782 (意法半导体) 32 Mbit (2Mb x 16, Dual Bank, Burst ) 1.8V Supply Flash Memory PDF资料下载
参数资料
| 型号： | 7782 |
| 厂商： | 意法半导体 |
| 英文描述： | 32 Mbit (2Mb x 16, Dual Bank, Burst ) 1.8V Supply Flash Memory |
| 中文描述： | 32兆位（含2Mb × 16，双行，突发）1.8V电源快闪记忆体 |
| 文件页数： | 27/63页 |
| 文件大小： | 435K |
| 代理商： | 7782 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页
27/63
M58CR032C, M58CR032D
BLOCK LOCKING
The M58CR032 features an instant, individual
block locking scheme that allows any block to be
locked or unlocked with no latency. This locking
scheme has three levels of protection.
I
Lock/Unlock - this first level allows software-
only control of block locking.
I
Lock-Down - this second level requires
hardware interaction before locking can be
changed.
I
V
PP
≤
V
PPLK
- the third level offers a complete
hardware protection against program and erase
on all blocks.
For all devices the protection status of each block
can be set to Locked, Unlocked, and Lock-Down.
Table 14, defines all of the possible protection
states (WP, DQ1, DQ0), and Appendix B, Figure
24, shows a flowchart for the locking operations.
Reading a Block’s Lock Status
The lock status of every block can be read in the
Read Electronic Signature mode of the device. To
enter this mode write 90h to the device. Subse-
quent reads at the address specified in Table 9,
will output the protection status of that block. The
lock status is represented by DQ0 and DQ1. DQ0
indicates the Block Lock/Unlock status and is set
by the Lock command and cleared by the Unlock
command. It is also automatically set when enter-
ing Lock-Down. DQ1 indicates the Lock-Down sta-
tus and is set by the Lock-Down command. It
cannot be cleared by software, only by a hardware
reset or power-down.
The following sections explain the operation of the
locking system.
Locked State
The default status of all blocks on power-up or af-
ter a hardware reset is Locked (states (0,0,1) or
(1,0,1)). Locked blocks are fully protected from
any program or erase. Any program or erase oper-
ations attempted on a locked block will return an
error in the Status Register. The Status of a
Locked block can be changed to Unlocked or
Lock-Down using the appropriate software com-
mands. An Unlocked block can be Locked by issu-
ing the Lock command.
Unlocked State
Unlocked blocks (states (0,0,0), (1,0,0) (1,1,0)),
can be programmed or erased. All unlocked
blocks return to the Locked state after a hardware
reset or when the device is powered-down. The
status of an unlocked block can be changed to
Locked or Locked-Down using the appropriate
software commands. A locked block can be un-
locked by issuing the Unlock command.
Lock-Down State
Blocks that are Locked-Down (state (0,1,x))are
protected from program and erase operations (as
for Locked blocks) but their protection status can-
not be changed using software commands alone.
A Locked or Unlocked block can be Locked-Down
by issuing the Lock-Down command. Locked-
Down blocks revert to the Locked state when the
device is reset or powered-down.
The Lock-Down function is dependent on the WP
input pin. When WP=0 (V
IL
), the blocks in the
Lock-Down state (0,1,x) are protected from pro-
gram, erase and protection status changes. When
WP=1 (V
IH
) the Lock-Down function is disabled
(1,1,1) and Locked-Down blocks can be individu-
ally unlocked to the (1,1,0) state by issuing the
software command, where they can be erased and
programmed. These blocks can then be re-locked
(1,1,1) and unlocked (1,1,0) as desired while WP
remains high. When WP is low , blocks that were
previously Locked-Down return to the Lock-Down
state (0,1,x) regardless of any changes made
while WP was high. Device reset or power-down
resets all blocks , including those in Lock-Down, to
the Locked state.
Locking Operations During Erase Suspend
Changes to block lock status can be performed
during an erase suspend by using the standard
locking command sequences to unlock, lock or
lock-down a block. This is useful in the case when
another block needs to be updated while an erase
operation is in progress.
To change block locking during an erase opera-
tion, first write the Erase Suspend command, then
check the status register until it indicates that the
erase operation has been suspended. Next write
the desired Lock command sequence to a block
and the lock status will be changed. After complet-
ing any desired lock, read, or program operations,
resume the erase operation with the Erase Re-
sume command.
If a block is locked or locked-down during an erase
suspend of the same block, the locking status bits
will be changed immediately, but when the erase
is resumed, the erase operation will complete.
Locking operations cannot be performed during a
program suspend. Refer to Appendix C, Com-
mand Interface State Table, for detailed informa-
tion on which commands are valid during erase
suspend.
相关PDF资料 |
PDF描述 |
|---|---|
| 7801-301XC | HIGH SPEED, BUFFER AMPLIFIER AMP |
| 78042FG | 1 watt dc-dc converters |
| 78044F | Common to 78K/0 Series |
| 780058 | Common to 78K/0 Series |
| 780058Y | Common to 78K/0 Series |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 778200-01 | 制造商:NI 制造商全称:National Instruments Corporation 功能描述:4-Channel Monochrome Image Acquisition |
| 778201-01 | 制造商:NI 制造商全称:National Instruments Corporation 功能描述:Real-Time Embedded Controllers for PXI |
| 778204-01 | 制造商:NI 制造商全称:National Instruments Corporation 功能描述:S Series Multifunction DAQ 12 or 16-Bit,1 to 10 MS/s, 4 Analog Inputs |
| 778218-000 | 制造商:TE Connectivity 功能描述:WALLBOX KIT LAN OUTLET WHITE |
| 77-82500 | 功能描述:D-Sub微型D连接器 50P R/A SOCKET HIGH/STD HOOD RoHS:否 制造商:3M Electronic Solutions Division 位置/触点数量:26 排数:2 安装风格:SMD/SMT 安装角:Right 端接类型:Solder 型式:Female |
发布紧急采购，3分钟左右您将得到回复。