参数资料
| 型号： | A3PN060-Z1VQG100I |
| 厂商： | Microsemi SoC |
| 文件页数： | 102/114页 |
| 文件大小： | 0K |
| 描述： | IC FPGA NANO 60K GATES 100-VQFP |
| 标准包装： | 90 |
| 系列： | ProASIC3 nano |
| RAM 位总计： | 18432 |
| 输入/输出数： | 71 |
| 门数： | 60000 |
| 电源电压： | 1.425 V ~ 1.575 V |
| 安装类型： | 表面贴装 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 100-TQFP |
| 供应商设备封装： | 100-VQFP（14x14） |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页当前第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页
Pin Descriptions and Packaging
3-2
Revision 11
gives greater flexibility in supply selection and simplifies power supply and PCB design. If the JTAG
interface is neither used nor planned for use, the VJTAG pin together with the TRST pin could be tied to
GND. It should be noted that VCC is required to be powered for JTAG operation; VJTAG alone is
insufficient. If a device is in a JTAG chain of interconnected boards, the board containing the device can
be powered down, provided both VJTAG and VCC to the part remain powered; otherwise, JTAG signals
will not be able to transition the device, even in bypass mode.
Microsemi recommends that VPUMP and VJTAG power supplies be kept separate with independent
filtering capacitors rather than supplying them from a common rail.
VPUMP
Programming Supply Voltage
ProASIC3 devices support single-voltage ISP of the configuration flash and FlashROM. For
programming, VPUMP should be 3.3 V nominal. During normal device operation, VPUMP can be left
floating or can be tied (pulled up) to any voltage between 0 V and the VPUMP maximum. Programming
power supply voltage (VPUMP) range is listed in the datasheet.
When the VPUMP pin is tied to ground, it will shut off the charge pump circuitry, resulting in no sources of
oscillation from the charge pump circuitry.
For proper programming, 0.01 F and 0.33 F capacitors (both rated at 16 V) are to be connected in
parallel across VPUMP and GND, and positioned as close to the FPGA pins as possible.
Microsemi recommends that VPUMP and VJTAG power supplies be kept separate with independent
filtering capacitors rather than supplying them from a common rail.
User Pins
I/O
User Input/Output
The I/O pin functions as an input, output, tristate, or bidirectional buffer. Input and output signal levels are
compatible with the I/O standard selected.
During programming, I/Os become tristated and weakly pulled up to VCCI. With VCCI, VMV, and VCC
supplies continuously powered up, when the device transitions from programming to operating mode, the
I/Os are instantly configured to the desired user configuration.
Unused I/Os are configured as follows:
Output buffer is disabled (with tristate value of high impedance)
Input buffer is disabled (with tristate value of high impedance)
Weak pull-up is programmed
GL
Globals
GL I/Os have access to certain clock conditioning circuitry (and the PLL) and/or have direct access to the
global network (spines). Additionally, the global I/Os can be used as regular I/Os, since they have
identical capabilities. Unused GL pins are configured as inputs with pull-up resistors.
See more detailed descriptions of global I/O connectivity in the "Clock Conditioning Circuits in Low Power
Flash Devices and Mixed Signal FPGAs" chapter of the ProASIC3 nano Device Family User’s Guide. All
inputs labeled GC/GF are direct inputs into the quadrant clocks. For example, if GAA0 is used for an
input, GAA1 and GAA2 are no longer available for input to the quadrant globals. All inputs labeled
GC/GF are direct inputs into the chip-level globals, and the rest are connected to the quadrant globals.
The inputs to the global network are multiplexed, and only one input can be used as a global input.
Refer to the I/O Structure chapter of the ProASIC3 nano Device Family User’s Guide for an explanation
of the naming of global pins.
相关PDF资料 |
PDF描述 |
|---|---|
| A3PN060-1VQ100I | IC FPGA NANO 60K GATES 100-VQFP |
| A3PN060-1VQG100I | IC FPGA NANO 60K GATES 100-VQFP |
| A3P030-2QNG132I | IC FPGA 1KB FLASH 30K 132-QFN |
| A3P125-1QNG132 | IC FPGA 1KB FLASH 125K 132-QFN |
| A3PN125-Z2VQ100 | IC FPGA NANO 125K GATES 100-VQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A3PN060-Z2VQ100 | 功能描述:IC FPGA NANO 60K GATES 100-VQFP RoHS:否 类别:集成电路 (IC) >> 嵌入式 - FPGA（现场可编程门阵列） 系列:ProASIC3 nano 标准包装:152 系列:IGLOO PLUS LAB/CLB数:- 逻辑元件/单元数:792 RAM 位总计:- 输入/输出数:120 门数:30000 电源电压:1.14 V ~ 1.575 V 安装类型:表面贴装 工作温度:-40°C ~ 85°C 封装/外壳:289-TFBGA，CSBGA 供应商设备封装:289-CSP（14x14） |
| A3PN060-Z2VQ100I | 功能描述:IC FPGA NANO 60K GATES 100-VQFP RoHS:否 类别:集成电路 (IC) >> 嵌入式 - FPGA（现场可编程门阵列） 系列:ProASIC3 nano 标准包装:152 系列:IGLOO PLUS LAB/CLB数:- 逻辑元件/单元数:792 RAM 位总计:- 输入/输出数:120 门数:30000 电源电压:1.14 V ~ 1.575 V 安装类型:表面贴装 工作温度:-40°C ~ 85°C 封装/外壳:289-TFBGA，CSBGA 供应商设备封装:289-CSP（14x14） |
| A3PN060-Z2VQG100 | 功能描述:IC FPGA NANO 60K GATES 100-VQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - FPGA（现场可编程门阵列） 系列:ProASIC3 nano 标准包装:152 系列:IGLOO PLUS LAB/CLB数:- 逻辑元件/单元数:792 RAM 位总计:- 输入/输出数:120 门数:30000 电源电压:1.14 V ~ 1.575 V 安装类型:表面贴装 工作温度:-40°C ~ 85°C 封装/外壳:289-TFBGA，CSBGA 供应商设备封装:289-CSP（14x14） |
| A3PN060-Z2VQG100I | 功能描述:IC FPGA NANO 60K GATES 100-VQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - FPGA（现场可编程门阵列） 系列:ProASIC3 nano 标准包装:152 系列:IGLOO PLUS LAB/CLB数:- 逻辑元件/单元数:792 RAM 位总计:- 输入/输出数:120 门数:30000 电源电压:1.14 V ~ 1.575 V 安装类型:表面贴装 工作温度:-40°C ~ 85°C 封装/外壳:289-TFBGA，CSBGA 供应商设备封装:289-CSP（14x14） |
| A3PN060-ZVQ100 | 功能描述:IC FPGA NANO 60K GATES 100-VQFP RoHS:否 类别:集成电路 (IC) >> 嵌入式 - FPGA（现场可编程门阵列） 系列:ProASIC3 nano 标准包装:152 系列:IGLOO PLUS LAB/CLB数:- 逻辑元件/单元数:792 RAM 位总计:- 输入/输出数:120 门数:30000 电源电压:1.14 V ~ 1.575 V 安装类型:表面贴装 工作温度:-40°C ~ 85°C 封装/外壳:289-TFBGA，CSBGA 供应商设备封装:289-CSP（14x14） |
发布紧急采购，3分钟左右您将得到回复。