参数资料
| 型号： | AD5371BSTZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 13/29页 |
| 文件大小： | 0K |
| 描述： | IC DAC 14BIT 40CH SER 80-LQFP |
| 标准包装： | 1 |
| 设置时间： | 20µs |
| 位数： | 14 |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 40 |
| 电压电源： | 模拟和数字，双 ± |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 80-LQFP |
| 供应商设备封装： | 80-LQFP（12x12） |
| 包装： | 托盘 |
| 输出数目和类型： | 40 电压，单极；40 电压，双极 |
| 采样率（每秒）： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
AD5371
Rev. B | Page 19 of 28
Reference Selection Example
If
Nominal output range = 12 V (4 V to +8 V)
Zero-scale error = ±70 mV
Gain error = ±3%, and
SIGGNDx = AGND = 0 V
Then
Gain error = ±3%
=> Maximum positive gain error = 3%
=> Output range including gain error = 12 + 0.03(12) = 12.36 V
Zero-scale error = ±70 mV
=> Maximum offset error span = 2(70 mV) = 0.14 V
=> Output range including gain error and zero-scale error =
12.36 V + 0.14 V = 12.5 V
VREF calculation
Actual output range = 12.5 V, that is, 4.25 V to +8.25 V;
VREF = (8.25 V + 4.25 V)/4 = 3.125 V
If the solution yields an inconvenient reference level, the user
can adopt one of the following approaches:
Use a resistor divider to divide down a convenient, higher
reference level to the required level.
Select a convenient reference level above VREF and modify
the gain and offset registers to digitally downsize the reference.
In this way, the user can use almost any convenient reference
level but can reduce the performance by overcompaction of
the transfer function.
Use a combination of these two approaches.
CALIBRATION
The user can perform a system calibration on the AD5371 to
reduce gain and offset errors to below 1 LSB. This reduction is
achieved by calculating new values for the M and C registers and
reprogramming them.
The M and C registers should not be programmed until both
the zero-scale and full-scale errors are calculated.
Reducing Zero-Scale Error
Zero-scale error can be reduced as follows:
1.
Set the output to the lowest possible value.
2.
Measure the actual output voltage and compare it to the
required value. This gives the zero-scale error.
3.
Calculate the number of LSBs equivalent to the error and
add this number to the default value of the C register. Note
that only negative zero-scale error can be reduced.
Reducing Full-Scale Error
Full-scale error can be reduced as follows:
1.
Measure the zero-scale error.
2.
Set the output to the highest possible value.
3.
Measure the actual output voltage and compare it to the
required value. Add this error to the zero-scale error. This
is the span error, which includes the full-scale error.
4.
Calculate the number of LSBs equivalent to the span error
and subtract this number from the default value of the M
register. Note that only positive full-scale error can be
reduced.
AD5371 Calibration Example
This example assumes that a 4 V to +8 V output is required.
The DAC output is set to 4 V but measured at 4.03 V. This
gives a zero-scale error of 30 mV.
1 LSB = 12 V/16,384 = 732.42 μV
30 mV = 41 LSBs
The full-scale error can now be calculated. The output is set to
8 V and a value of 8.02 V is measured. This gives a full-scale
error of +20 mV and a span error of +20 mV (30 mV) =
+50 mV.
50 mV = 68 LSBs
The errors can now be removed as follows:
1.
Add 41 LSBs to the default C register value:
8192 + 41 = 8233
2.
Subtract 68 LSBs from the default M register value:
16,383 68 = 16,315
3.
Program the M register to 16,315; program the C register
to 8233.
ADDITIONAL CALIBRATION
The techniques described in the previous section are usually
enough to reduce the zero-scale and full-scale errors in most
applications. However, there are limitations whereby the errors
may not be sufficiently reduced. For example, the offset (C)
register can only be used to reduce the offset caused by the
negative zero-scale error. A positive offset cannot be reduced.
Likewise, if the maximum voltage is below the ideal value, that
is, a negative full-scale error, the gain (M) register cannot be
used to increase the gain to compensate for the error.
These limitations can be overcome by increasing the reference
value. With a 3 V reference, a 12 V span is achieved. The ideal
voltage range for the AD5371 is 4 V to +8 V. Using a +3.1 V
reference increases the range to 4.133 V to +8.2667 V. Clearly,
in this case, the offset and gain errors are insignificant, and the
M and C registers can be used to raise the negative voltage to
4 V and then reduce the maximum voltage to +8 V to give the
most accurate values possible.
相关PDF资料 |
PDF描述 |
|---|---|
| AD5383BSTZ-5 | IC DAC 12BIT 32CH 5V 100-LQFP |
| AD5384BBCZ-5 | IC DAC 14BIT 40CH 5V 100-CSPBGA |
| AD5398BCPZ-REEL | IC DAC 10BIT CURRENT-SINK 8LFCSP |
| AD5420AREZ-REEL7 | IC DAC 16BIT 1CH SER 24TSSOP |
| AD5425YRM | IC DAC MULTIPLYING 8BIT 10-MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD5371BSTZ-REEL | 功能描述:IC DAC 14BIT 40CH SER 80-LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1,000 系列:- 设置时间:1µs 位数:8 数据接口:串行 转换器数目:8 电压电源:双 ± 功率耗散（最大）:941mW 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC W 包装:带卷 (TR) 输出数目和类型:8 电压，单极 采样率（每秒）:* |
| AD5372 | 制造商:AD 制造商全称:Analog Devices 功能描述:32-Channel, 16/14, Serial Input, Voltage-Output DACs |
| AD5372BCPZ | 制造商:Analog Devices 功能描述:DAC 32CH-CH RES-STRING 16BIT 56LFCSP EP - Trays |
| AD5372BCPZ-REEL7 | 制造商:Analog Devices 功能描述:DAC 32CH-CH RES-STRING 16BIT 56LFCSP EP - Tape and Reel |
| AD5372BCPZ-RL7 | 功能描述:16 Bit Digital to Analog Converter 32 56-LFCSP-VQ (8x8) 制造商:analog devices inc. 系列:- 包装:带卷（TR） 零件状态:上次购买时间 位数:16 数模转换器数:32 建立时间:30μs 输出类型:Voltage - Buffered 差分输出:无 数据接口:SPI，DSP 参考类型:外部 电压 - 电源，模拟:9 V ~ 16.5 V，-4.5 V ~ 16.5 V 电压 - 电源，数字:2.5 V ~ 5.5 V INL/DNL（LSB）:±4（最大），±1（最大） 架构:电阻串 DAC 工作温度:-40°C ~ 85°C 封装/外壳:56-VFQFN 裸露焊盘，CSP 供应商器件封装:56-LFCSP-VQ（8x8） 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。