参数资料
| 型号： | AD5735ACPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 32/48页 |
| 文件大小： | 0K |
| 描述： | IC DAC QUAD VOLT CUR 64-LFCSP |
| 标准包装： | 1 |
| 设置时间： | 18µs |
| 位数： | 12 |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 4 |
| 电压电源： | 模拟和数字，双 ± |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 64-LFCSP-VQ（9x9） |
| 包装： | 托盘 |
| 输出数目和类型： | 4 电流，4 电压 |
| 采样率（每秒）： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页当前第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
AD5735
Data Sheet
Rev. C | Page 38 of 48
Status Register
The status register is a read-only register. This register contains
any fault information, as a well as a ramp active bit (Bit D9) and
a user toggle bit (Bit D11). When the STATREAD bit in the
main control register is set, the status register contents can be
read back on the SDO pin during every write sequence. Alterna-
tively, if the STATREAD bit is not set, the status register can be
read using the normal readback operation (see the Readback
Operation section).
Table 32. Decoding the Status Register
MSB
LSB
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
DC-DCD DC-DCC DC-DCB DC-DCA User
toggle
PEC
error
Ramp
active
Over
temp
V
OUT_D
fault
V
OUT_C
fault
V
OUT_B
fault
V
OUT_A
fault
I
OUT_D
fault
I
OUT_C
fault
I
OUT_B
fault
I
OUT_A
fault
Table 33. Status Register Bit Descriptions
Bit Name
Description
DC-DCD
In current output mode, this bit is set if the dc-to-dc converter on Channel D cannot maintain compliance, for example, if
the dc-to-dc converter is reaching its V
Functionality section for more information about the operation of this bit under this condition.
In voltage output mode, this bit is set if the dc-to-dc converter on Channel D is unable to regulate to 15 V as expected.
When this bit is set, it does not result in the FAULT pin going high.
DC-DCC
In current output mode, this bit is set if the dc-to-dc converter on Channel C cannot maintain compliance, for example, if
the dc-to-dc converter is reaching its V
Functionality section for more information about the operation of this bit under this condition.
In voltage output mode, this bit is set if the dc-to-dc converter on Channel C is unable to regulate to 15 V as expected.
When this bit is set, it does not result in the FAULT pin going high.
DC-DCB
In current output mode, this bit is set if the dc-to-dc converter on Channel B cannot maintain compliance, for example, if
the dc-to-dc converter is reaching its V
Functionality section for more information about the operation of this bit under this condition.
In voltage output mode, this bit is set if the dc-to-dc converter on Channel B is unable to regulate to 15 V as expected.
When this bit is set, it does not result in the FAULT pin going high.
DC-DCA
In current output mode, this bit is set if the dc-to-dc converter on Channel A cannot maintain compliance, for example, if
the dc-to-dc converter is reaching its V
Functionality section for more information about the operation of this bit under this condition.
In voltage output mode, this bit is set if the dc-to-dc converter on Channel A is unable to regulate to 15 V as expected.
When this bit is set, it does not result in the FAULT pin going high.
User Toggle
User toggle bit. This bit is set or cleared via the software register and can be used to verify data communications, if needed.
PEC Error
Denotes a PEC error on the last data-word received over the SPI interface.
Ramp Active
This bit is set while any output channel is slewing (digital slew rate control is enabled on at least one channel).
Over Temp
This bit is set if the AD5735 core temperature exceeds approximately 150°C.
V
OUT_D Fault
This bit is set if a fault is detected on the V
OUT_D pin.
V
OUT_C Fault
This bit is set if a fault is detected on the V
OUT_C pin.
V
OUT_B Fault
This bit is set if a fault is detected on the V
OUT_B pin.
V
OUT_A Fault
This bit is set if a fault is detected on the V
OUT_A pin.
I
OUT_D Fault
This bit is set if a fault is detected on the I
OUT_D pin.
I
OUT_C Fault
This bit is set if a fault is detected on the I
OUT_C pin.
I
OUT_B Fault
This bit is set if a fault is detected on the I
OUT_B pin.
I
OUT_A Fault
This bit is set if a fault is detected on the I
OUT_A pin.
相关PDF资料 |
PDF描述 |
|---|---|
| AD5044BRUZ | IC DAC QUAD 14BIT SPI 16TSSOP |
| MS3454W24-22S | CONN RCPT 4POS JAM NUT W/SCKT |
| ADV7125JSTZ330 | IC DAC VIDEO 3CH 330MHZ 48LQFP |
| VE-21N-MY-F2 | CONVERTER MOD DC/DC 18.5V 50W |
| LTC2625IGN#PBF | IC DAC 12BIT R-R OCT 16SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD5735ACPZ-REEL7 | 功能描述:IC DAC QUAD VOLT CUR 64LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:Data Converter Fundamentals DAC Architectures 标准包装:750 系列:- 设置时间:7µs 位数:16 数据接口:并联 转换器数目:1 电压电源:双 ± 功率耗散（最大）:100mW 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-LCC（J 形引线） 供应商设备封装:28-PLCC（11.51x11.51） 包装:带卷 (TR) 输出数目和类型:1 电压，单极；1 电压，双极 采样率（每秒）:143k |
| AD5737 | 制造商:AD 制造商全称:Analog Devices 功能描述:Quad Channel, 16-Bit, Serial Input, 4-20mA Output DAC, Dynamic Power Control, HART Connectivity |
| AD5737_12 | 制造商:AD 制造商全称:Analog Devices 功能描述:Quad-Channel, 12-Bit, Serial Input, 4 mA to 20 mA Output |
| AD5737ACPZ | 功能描述:IC DAC QUAD 12BIT CUR 64-LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 标准包装:1 系列:- 设置时间:4.5µs 位数:12 数据接口:串行，SPI? 转换器数目:1 电压电源:单电源 功率耗散（最大）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOICN 包装:剪切带 (CT) 输出数目和类型:1 电压，单极；1 电压，双极 采样率（每秒）:* 其它名称:MCP4921T-E/SNCTMCP4921T-E/SNRCTMCP4921T-E/SNRCT-ND |
| AD5737ACPZ-RL7 | 制造商:AD 制造商全称:Analog Devices 功能描述:Quad-Channel, 12-Bit, Serial Input, 4 mA to 20 mA Output |
发布紧急采购，3分钟左右您将得到回复。