参数资料
| 型号： | AD5757ACPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 31/44页 |
| 文件大小： | 0K |
| 描述： | IC DAC 16BIT QUAD 64-LFCSP |
| 特色产品： | AD5755 / AD5755-1 / AD5757 DACs |
| 标准包装： | 1 |
| 设置时间： | 15µs |
| 位数： | 16 |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 4 |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 64-LFCSP-VQ（9x9） |
| 包装： | 管件 |
| 输出数目和类型： | * |
| 采样率（每秒）： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页当前第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
Data Sheet
AD5757
Rev. D | Page 37 of 44
Table 33. Recommended DC-to-DC Components
Symbol
Component
Value
Manufacturer
L
DCDC
XAL4040-103
10 H
Coilcraft
C
DCDC
GRM32ER71H475KA88L
4.7 F
Murata
D
DCDC
PMEG3010BEA
0.38 V
F
NXP
It is recommended to place a 10 , 100 nF low-pass RC filter
after CDCDC. This consumes a small amount of power but
reduces the amount of ripple on the VBOOST_x supply.
DC-to-DC Converter Operation
The on-board dc-to-dc converters use a constant frequency,
peak current mode control scheme to step up an AVCC input of
4.5 V to 5.5 V to drive the AD5757 output channel. These are
designed to operate in discontinuous conduction mode (DCM)
with a duty cycle of <90% typical. Discontinuous conduction
mode refers to a mode of operation where the inductor current
goes to zero for an appreciable percentage of the switching
cycle. The dc-to-dc converters are nonsynchronous; that is,
they require an external Schottky diode.
DC-to-DC Converter Output Voltage
When a channel current output is enabled, the converter regulates
the VBOOST_x supply to 7.4 V (±5%) or (IOUT × RLOAD + Headroom),
whichever is greater (see Figure 31 for a plot of headroom
supplied vs. output current). When the output is disabled, the
converter regulates the VBOOST_x supply to 7.4 V (±5%).
DC-to-DC Converter Settling Time
The settling time for a step greater than ~1 V (IOUT × RLOAD) is
dominated by the settling time of the dc-to-dc converter. The
exception to this is when the required voltage at the IOUT_x pin plus
the compliance voltage is below 7.4 V (±5%). A typical plot of the
output settling time can be found in Figure 26. This plot is for a
1 k load. The settling time for smaller loads is faster. The
settling time for current steps less than 24 mA is also faster.
DC-to-DC Converter VMAX Functionality
The maximum VBOOST_x voltage is set in the dc-to-dc control
register (23 V, 24.5 V, 27 V, or 29.5 V; see Table 24). On reaching
this maximum voltage, the dc-to-dc converter is disabled, and
the VBOOST_x voltage is allowed to decay by ~0.4 V. After the
VBOOST_x voltage has decayed by ~0.4 V, the dc-to-dc converter
is reenabled, and the voltage ramps up again to VMAX, if still
required. This operation is shown in Figure 57.
28.6
28.7
28.8
28.9
29.0
29.1
29.2
29.3
29.4
29.5
29.6
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
V
B
OOS
T
VO
L
T
A
G
E
(V)
TIME (ms)
VMAX
0mA TO 24mA RANGE, 24mA OUTPUT
OUTPUT UNLOADED
DC-DCMaxV = 29.5V
DC_DC BIT
DC-DCx BIT = 0
DC-DCx BIT = 1
f
SW = 410kHz
TA = 25°C
09225-
183
Figure 57. Operation on Reaching VMAX
As shown in Figure 57, the DC-DCx bit in the status register
asserts when the AD5757 is ramping to the VMAX value but
deasserts when the voltage is decaying to VMAX ~0.4 V.
DC-to-DC Converter On-Board Switch
The AD5757 contains a 0.425 internal switch. The switch
current is monitored on a pulse by pulse basis and is limited to
0.8 A peak current.
DC-to-DC Converter Switching Frequency and Phase
The AD5757 dc-to-dc converter switching frequency can be
selected from the dc-to-dc control register. The phasing of the
channels can also be adjusted so that the dc-to-dc converter can
clock on different edges (see Table 24). For typical applications,
a 410 kHz frequency is recommended. At light loads (low output
current and small load resistor), the dc-to-dc converter enters a
pulse-skipping mode to minimize switching power dissipation.
DC-to-DC Converter Inductor Selection
For typical 4 mA to 20 mA applications, a 10 H inductor (such
as the XAL4040-103 from Coilcraft), combined with a switch-
ing frequency of 410 kHz, allows up to 24 mA to be driven into a
load resistance of up to 1 k with an AVCC supply of 4.5 V to
5.5 V. It is important to ensure that the inductor is able to handle
the peak current without saturating, especially at the maximum
ambient temperature. If the inductor enters into saturation mode,
it results in a decrease in efficiency. The inductance value also
drops during saturation and may result in the dc-to-dc converter
circuit not being able to supply the required output power.
DC-to-DC Converter External Schottky Selection
The AD5757 requires an external Schottky for correct
operation. Ensure that the Schottky is rated to handle the
maximum reverse breakdown expected in operation and that
the rectifier maximum junction temperature is not exceeded.
The diode average current is approximately equal to the ILOAD
current. Diodes with larger forward voltage drops result in a
decrease in efficiency.
相关PDF资料 |
PDF描述 |
|---|---|
| MS3122E16-23S | CONN RCPT 23POS BOX MNT W/SCKT |
| MS27497T18A32PLC | CONN HSG RCPT 32POS WALL MT PINS |
| AD7225KNZ | IC DAC 8BIT QUAD W/AMP 24DIP |
| VE-2WL-MY-F4 | CONVERTER MOD DC/DC 28V 50W |
| AD7537KRZ | IC DAC 12BIT DUAL MULT 24SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD5757ACPZ-REEL7 | 功能描述:IC DAC 16BIT QUAD IOUT 64LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:Data Converter Fundamentals DAC Architectures 标准包装:750 系列:- 设置时间:7µs 位数:16 数据接口:并联 转换器数目:1 电压电源:双 ± 功率耗散（最大）:100mW 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-LCC（J 形引线） 供应商设备封装:28-PLCC（11.51x11.51） 包装:带卷 (TR) 输出数目和类型:1 电压，单极；1 电压，双极 采样率（每秒）:143k |
| AD5757X | 制造商:AD 制造商全称:Analog Devices 功能描述:Quad Channel, 16-Bit, Serial Input, 4-20mA Output DAC, Dynamic Power Control, HART Connectivity |
| AD575JD | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog-to-Digital Converter， 10-Bit |
| AD575JN | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog-to-Digital Converter， 10-Bit |
| AD575KD | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog-to-Digital Converter， 10-Bit |
发布紧急采购，3分钟左右您将得到回复。