- 您现在的位置：买卖IC网 > PDF目录373890 > AD6624AS (ANALOG DEVICES INC) Four-Channel, 80 MSPS Digital Receive Signal Processor (RSP) PDF资料下载
参数资料
| 型号： | AD6624AS |
| 厂商： | ANALOG DEVICES INC |
| 元件分类： | 通信及网络 |
| 英文描述： | Four-Channel, 80 MSPS Digital Receive Signal Processor (RSP) |
| 中文描述： | SPECIALTY TELECOM CIRCUIT, PQFP128 |
| 封装： | PLASTIC, MQFP-128 |
| 文件页数： | 14/40页 |
| 文件大小： | 506K |
| 代理商： | AD6624AS |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
REV. B
AD6624
–14–
EXAMPLE FILTER RESPONSE
kHz
10
–1000
1000
d
–800 –600 –400 –200
0
200
400
600
800
0
–50
–60
–70
–20
–30
–40
–10
0
–80
–90
–100
–110
–120
–130
–140
–150
Figure 19. Filter Response
The filter in Figure 19 is based on a 65 MSPS input data rate
and an output rate of 541.6666 kSPS (two samples per symbol
for EDGE). Total decimation rate is 120 distributed between
the rCIC2, CIC5, and RCF.
kHz
10
d
–500
–400
–200
0
200
400
500
0
–50
–60
–70
–20
–30
–40
–10
–80
–90
–100
–110
–120
–130
–140
–150
Figure 20. Filter Response
The filter in Figure 20 is designed to meet the IS-136 specifica-
tions. For this configuration, the clock is set to 61.44 MSPS
with a total decimation rate of 320 providing an output data
rate of 192 kSPS or four samples per symbol.
INPUT DATA PORTS
The AD6624 features dual, high speed ADC input ports, Input
Port A and Input Port B. The dual input ports allow for the
most flexibility with a single tuner chip. These can be diversity
inputs or truly independent inputs such as separate antenna
segments. Either ADC port can be routed to one of four tuner
channels. For added flexibility, each input port can be used to
support multiplexed inputs such as those found on the AD6600
or other ADCs with muxed outputs. This added flexibility
can allow for up to four different analog sources to be pro-
cessed simultaneously by the four internal channels.
In addition, the front end of the AD6624 contains circuitry that
enables high speed signal level detection and control. This is
accomplished with a unique high speed level detection circuit
that offers minimal latency and maximum flexibility to control
up to four analog signal paths. The overall signal path latency
from input to output on the AD6624 can be expressed in high-
speed clock cycles. The equation below can be used to calculate
the latency.
T
LATENCY
=
M
rC1C2
(
M
CIC5
+ 7) +
N
TAPS
= 4(
SDIV
+ 1) +18
M
rC1C2
and
M
CIC5
are decimation values for the rC1C2 and
CIC5 filters, respectively,
N
TAPS
is the number RCF taps cho-
sen, and
SDIV
is the chosen SCLK divisor factor.
Input Data Format
Each input port consists of a 14-bit mantissa and 3-bit exponent. If
interfacing to a standard ADC is required, the exponent bits can
be grounded. If connected to a floating point ADC such as the
AD6600, the exponent bits from that product can be connected
to the input exponent bits of the AD6624. The mantissa data
format is twos complement and the exponent is unsigned binary.
Input Timing
The data from each high speed input port is latched on the
rising edge of CLK. This clock signal is used to sample the
input port and clock the synchronous signal processing stages
that follow in the selected channels.
CLK
IN[13:0]
EXP[2:0]
DATA
t
SI
t
HI
Figure 21. Input Data Timing Requirements
The clock signals can operate up to 80 MHz and have a 50% duty
cycle. In applications using high-speed ADCs, the ADC sample
clock or data valid strobe is typically used to clock the AD6624.
CLK
t
CLK
t
CLKH
t
CLKL
Figure 22. CLK Timing Requirements
Input Enable Control
There is an IENA and an IENB pin for the Input Port A and
Input Port B, respectively. There are four modes of operation
used for each IEN pin. Using these modes, it is possible to
emulate operation of the other RSPs such as the AD6620, which
offer dual channel modes normally associated with diversity
operations. These modes are: IEN transition to low, IEN transi-
tion to high, IEN high, and blank on IEN low.
In the IEN high mode, the inputs and normal operations occur
when the Input Enable is high. In the IEN transition to low
mode, normal operations occur on the first rising edge of the
clock after the IEN transitions to low. Likewise, in the IEN
transition to high mode, operations occur on the rising edge of
the clock after the IEN transitions to high. See the Numerically
Controlled Oscillator section for more details on configuring the
Input Enable Modes. In blank on IEN low mode, the input data
is interpreted as zero when IEN is low.
相关PDF资料 |
PDF描述 |
|---|---|
| AD6624A | Four-Channel, 100 MSPS Digital Receive Signal Processor (RSP) |
| AD6624AABC | Four-Channel, 100 MSPS Digital Receive Signal Processor (RSP) |
| AD6630AR-REEL | Differential, Low Noise IF Gain Block with Output Clamping |
| AD6630AR | Differential, Low Noise IF Gain Block with Output Clamping |
| AD6630PCB | Differential, Low Noise IF Gain Block with Output Clamping |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD6624AS/PCB | 制造商:AD 制造商全称:Analog Devices 功能描述:Four-Channel, 100 MSPS Digital Receive Signal Processor (RSP) |
| AD6624S/PCB | 制造商:AD 制造商全称:Analog Devices 功能描述:Four-Channel, 80 MSPS Digital Receive Signal Processor (RSP) |
| AD662AQ | 制造商:未知厂家 制造商全称:未知厂家 功能描述:12-Bit Digital-to-Analog Converter |
| AD662BQ | 制造商:未知厂家 制造商全称:未知厂家 功能描述:12-Bit Digital-to-Analog Converter |
| AD662JN | 制造商:未知厂家 制造商全称:未知厂家 功能描述:12-Bit Digital-to-Analog Converter |
发布紧急采购，3分钟左右您将得到回复。