参数资料
| 型号： | AD7193BCPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 47/57页 |
| 文件大小： | 0K |
| 描述： | IC ADC 24BIT SPI 4.8KHZ 32LFCSP |
| 标准包装： | 1 |
| 位数： | 24 |
| 采样率（每秒）： | 4.8k |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 32-LFCSP-WQ（5x5） |
| 包装： | 托盘 |
| 输入数目和类型： | 4 个差分，单极；4 个差分，双极；8 个伪差分，单极；8 个伪差分，双极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页当前第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页
AD7193
Data Sheet
Rev. D | Page 50 of 56
FAST SETTLING MODE (SINC3 FILTER)
In fast settling mode, the settling time is close to the inverse of
the first filter notch. Therefore, the user can achieve 50 Hz and/or
60 Hz rejection at an output data rate close to 1/50 Hz or 1/60 Hz.
The settling time is equal to 1/output data rate. Therefore, the
conversion time is constant when converting on a single channel
or when converting on several channels. There is no added
latency when switching channels.
The fast settling mode is enabled using Bit AVG1 and Bit AVG0
in the mode register. A postfilter is included after the sinc4 filter.
The postfilter averages by 2, 8, or 16, depending on the settings
of the AVG1 and AVG0 bits.
SINC3/SINC4
POST FILTER
MODULATOR
ADC
CHOP
083
67
-05
5
Figure 61. Fast Settling Mode, Sinc3 Filter
Output Data Rate and Settling Time, Sinc3 Filter
With chop disabled, the output data rate is
fADC = fCLK/((3 + Avg – 1) × 1024 × FS[9:0])
fADC is the output data rate.
fCLK is master clock (4.92 MHz nominal).
Avg is the average.
FS[9:0] is the decimal equivalent of Bit FS9 to Bit FS0 in the
mode register.
If AVG1 = AVG0 = 0, the fast settling mode is not enabled.
In this case, the preceding equation is not relevant.
The settling time is equal to
tSETTLE = 1/fADC
Table 35 lists some sample FS words and the corresponding
output data rates and settling times.
Table 35. Examples of Output Data Rates and the
Corresponding Settling Time (Fast Settling Mode, Sinc3)
FS[9:0]
Average
Output Data Rate (Hz)
Settling Time (ms)
96
16
2.78
360
30
16
8.9
112.5
6
16
44.44
22.5
5
16
53.3
18.75
If the analog input channel is changed, there is no additional
delay in generating valid conversions and the device functions
as a zero latency ADC.
CHANNEL
CONVERSIONS
CHANNEL A
CH A
CH B
CHANNEL B
1/
fADC
CH B
0
83
67
-0
56
Figure 62. Fast Settling, Sinc3 Filter
When the device is converting on a single channel and a step
change occurs on the analog input, the ADC does not detect
the change and continues to output conversions. When the step
change is synchronized with the conversion, only fully settled
results are output from the ADC. However, if the step change is
asynchronous to the conversion process, one intermediate result
is not completely settled (see Figure 63).
ANALOG
INPUT
ADC
OUTPUT
VALID
1/
fADC
0
83
67
-0
57
Figure 63. Step Change on Analog Input, Sinc3 Filter
50 Hz/60 Hz Rejection, Sinc3 Filter
Figure 64 shows the frequency response when FS[9:0] is set to 6
and the postfilter averages by 16. This gives an output data rate
of 44.44 Hz when the master clock is 4.92 MHz. The sinc filter
places the first notch at
fNOTCH = fCLK/(1024 × FS[9:0])
The postfiltering places notches at fNOTCH/Avg (Avg is the amount
of averaging) and multiples of this frequency. Therefore, when
FS[9:0] is set to 6 and the postfilter averaging is 16, a notch is
placed at 800 Hz due to the sinc filter and notches are placed at
50 Hz and multiples of 50 Hz due to the postfilter.
The notch at 50 Hz is a first-order notch. Therefore, the notch is
not wide. This means that the rejection at 50 Hz exactly is good,
assuming a stable 4.92 MHz master clock. However, in a band of
50 Hz ± 1 Hz, the rejection degrades significantly. The rejection at
50 Hz ± 0.5 Hz is 40 dB minimum, assuming a stable clock; there-
fore, a good master clock source is recommended when using fast
settling mode.
08
36
7-
0
53
–120
–110
–100
–90
–80
–70
–60
–50
–40
–30
–20
–10
0
306090
120
150
FREQUENCY (Hz)
F
IL
T
E
R
GA
IN
(
d
B
)
Figure 64. Filter Response for Average + Decimate Filter
(Sinc3 Filter, FS[9:0] = 6, Average by 16)
相关PDF资料 |
PDF描述 |
|---|---|
| AD7194BCPZ | IC ADC 24BIT SPI 4.8K 32-LFCSP |
| AD7195BCPZ-RL7 | IC AFE 24BIT 4.8K 32LFSP |
| AD7225BQ | IC DAC 8BIT QUAD W/AMP 24-CDIP |
| AD7226BQ | IC DAC 8BIT QUAD W/AMP 20-CDIP |
| AD7228CQ | IC DAC 8BIT OCTAL W/AMP 24-CDIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7193BCPZ-RL | 功能描述:IC ADC 24BIT SPI 4.8KHZ 32LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD7193BCPZ-RL7 | 功能描述:IC ADC 24BIT SPI 4.8KHZ 32LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD7193BRUZ | 功能描述:IC ADC 24BIT SPI 4.8K 28-TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| AD7193BRUZ | 制造商:Analog Devices 功能描述:IC ADC 24BIT 4.8KHZ TSSOP-28 |
| AD7193BRUZ-REEL | 功能描述:IC ADC 24BIT SPI 4.8KHZ 28TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
发布紧急采购，3分钟左右您将得到回复。