参数资料
| 型号： | AD7195BCPZ-RL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 26/45页 |
| 文件大小： | 0K |
| 描述： | IC AFE 24BIT 4.8K 32LFSP |
| 设计资源： | Precision Weigh Scale Design Using AD7195 with Internal PGA and AC Excitation (CN0155) |
| 标准包装： | 1,500 |
| 位数： | 24 |
| 通道数： | 4 |
| 电压 - 电源，模拟： | 4.75 V ~ 5.25 V |
| 电压 - 电源，数字： | 2.7 V ~ 5.25 V |
| 封装/外壳： | 32-WFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 32-LFCSP-WQ（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页
AD7195
Rev. 0 | Page 31 of 44
Continuous Read
Rather than write to the communications register each time
a conversion is complete to access the data, the AD7195 can
be configured so that the conversions are placed on the
DOUT/RDY line automatically. By writing 01011100 to
the communications register, the user need only apply the
appropriate number of SCLK cycles to the ADC, and the
conversion word is automatically placed on the DOUT/RDY
line when a conversion is complete. The ADC should be
configured for continuous conversion mode.
When DOUT/RDY goes low to indicate the end of a conversion,
sufficient SCLK cycles must be applied to the ADC; the data
conversion is then placed on the DOUT/RDY line. When the
conversion is read, DOUT/RDY returns high until the next
conversion is available. In this mode, the data can be read only
once. Also, the user must ensure that the data-word is read
before the next conversion is complete. If the user has not read
the conversion before the completion of the next conversion,
or if insufficient serial clocks are applied to the AD7195 to
read the word, the serial output register is reset when the next
conversion is complete, and the new conversion is placed in
the output serial register.
To exit the continuous read mode, Instruction 01011000 must
be written to the communications register while the RDY pin
is low. While in continuous read mode, the ADC monitors
activity on the DIN line so that it can receive the instruction
to exit the continuous read mode. Additionally, a reset occurs
if 40 consecutive 1s are seen on DIN. Therefore, DIN should
be held low in continuous read mode until an instruction is to
be written to the device.
When several channels are enabled, the ADC continuously
steps through the enabled channels and performs one con-
version on each channel each time that it is selected. DOUT/
RDY pulses low when a conversion is available. When the user
applies sufficient SCLK pulses, the data is automatically placed
on the DOUT/RDY pin. If the DAT_STA bit in the mode
register is set to 1, the contents of the status register are output
along with the conversion. The status register indicates the
channel to which the conversion corresponds.
DIN
SCLK
DOUT/RDY
CS
0x5C
DATA
0
877
1-
0
31
Figure 23. Continuous Read
相关PDF资料 |
PDF描述 |
|---|---|
| AD7225BQ | IC DAC 8BIT QUAD W/AMP 24-CDIP |
| AD7226BQ | IC DAC 8BIT QUAD W/AMP 20-CDIP |
| AD7228CQ | IC DAC 8BIT OCTAL W/AMP 24-CDIP |
| AD7233BNZ | IC DAC 12BIT SRL W/AMP 8PDIP |
| AD7243BQ | IC DAC 12BIT W/AMP W/REF 16-CDIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD71L | 制造商:Johnson Components 功能描述:ADAPT - Bulk |
| AD72 | 制造商:Distributed By MCM 功能描述:REFRIGERATR DOOR GASKET DIRECT |
| AD720 | 制造商:AD 制造商全称:Analog Devices 功能描述:RGB to NTSC/PAL Encoders |
| AD720-00E | 功能描述:SENSOR MAG SW 28G STANDRD 8-MSOP 制造商:nve corp/sensor products 系列:AD 包装:管件 零件状态:有效 功能:全极开关 技术:霍尔效应 极化:任意一种 感应范围:±3.4mT 跳闸，±1.4mT 释放 测试条件:-40°C ~ 125°C 电压 - 电源:4.5 V ~ 30 V 电流 - 电源（最大值）:4.5mA 电流 - 输出（最大值）:20mA 输出类型:开路集电极 特性:- 工作温度:-40°C ~ 125°C（TA） 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商器件封装:8-MSOP 标准包装:1,000 |
| AD720-02E | 功能描述:SENSOR MAG SW 28G STANDARD 8SOIC 制造商:nve corp/sensor products 系列:AD 包装:管件 零件状态:有效 功能:全极开关 技术:霍尔效应 极化:任意一种 感应范围:±3.4mT 跳闸，±1.4mT 释放 测试条件:-40°C ~ 125°C 电压 - 电源:4.5 V ~ 30 V 电流 - 电源（最大值）:4.5mA 电流 - 输出（最大值）:20mA 输出类型:开路集电极 特性:- 工作温度:-40°C ~ 125°C（TA） 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商器件封装:8-SOIC 标准包装:1,000 |
发布紧急采购，3分钟左右您将得到回复。