- 您现在的位置：买卖IC网 > PDF目录10667 > AD7719BRUZ (Analog Devices Inc)IC ADC 16BIT 24BIT DUAL 28-TSSOP PDF资料下载
参数资料
| 型号： | AD7719BRUZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 2/40页 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT 24BIT DUAL 28-TSSOP |
| 标准包装： | 50 |
| 位数： | 16/24 |
| 采样率（每秒）： | 105 |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 2 |
| 功率耗散（最大）： | 4.5mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 28-TSSOP |
| 包装： | 管件 |
| 输入数目和类型： | 3 个差分，单极；3 个差分，双极 |
| 产品目录页面： | 778 (CN2011-ZH PDF) |
第1页当前第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
REV. A
AD7719
–10–
PIN FUNCTION DESCRIPTIONS (continued)
Pin No.
Mnemonic
Function
16
P2/SW2
Dual-Purpose Pin. It can act as a general-purpose output (P2) bit referenced between AVDD and AGND
or as a low-side power switch (SW2) to PWRGND.
17
PWRGND
Ground Point for the Low-Side Power Switches SW2 and SW1. PWRGND must be tied to AGND.
18
P1/SW1
Dual-Purpose Pin. It can act as a general-purpose output (P1) bit referenced between AVDD and AGND
or as a low-side power switch (SW1) to PWRGND.
19
RESET
Digital Input Used to Reset the ADC to Its Power-On Reset Status. This pin has a weak pull-up internally
to DVDD.
20
SCLK
Serial Clock Input for Data Transfers to and from the ADC. The SCLK has a Schmitt-triggered input,
making the interface suitable for opto-isolated applications. The serial clock can be continuous with all
data transmitted in a continuous train of pulses. Alternatively, it can be a noncontinuous clock with the
information being transmitted to or from the AD7719 in smaller batches of data. A weak pull-up to DVDD
is provided on the SCLK input.
21
CS
Chip Select Input. This is an active low logic input used to select the AD7719.
CS can be used to select
the AD7719 in systems with more than one device on the serial bus or as a frame synchronization signal in
communicating with the device.
CS can be hardwired low, allowing the AD7719 to be operated in 3-wire
mode with SCLK, DIN, and DOUT used to interface with the device. A weak pull-up to DVDD is provided
on the CS input.
22
RDY
RDY is a logic low status output from the AD7719. RDY is low if either the main ADC or auxiliary ADC
channel has valid data in its data register. This output returns high on completion of a read operation
from the data register. If data is not read,
RDY will return high prior to the next update, indicating to the
user that a read operation should not be initiated. The
RDY pin also returns low following the completion
of a calibration cycle. The
RDY pin is effectively the digital NOR function of the RDY0 and RDY1 bits in
the Status register. If one of the ADCs is disabled, the
RDY pin reflects the active ADC. RDY does not
return high after a calibration until the mode bits are written to, enabling a new conversion or calibration.
Since the
RDY pin provides information on both the main and aux ADCs, when either the main or aux
ADC is disabled, it is recommended to immediately read its data register to ensure that its RDY bit goes
inactive and releases the
RDY pin to indicate output data updates on the remaining active ADC.
23
DOUT
Serial Data Output Accessing the Output Shift Register of the AD7719. The output shift register can
contain data from any of the on-chip data, calibration, or control registers.
24
DIN
Serial Data Input Accessing the Input Shift Register on the AD7719. Data in this shift register is transferred
to the calibration or control registers within the ADC depending on the selection bits of the Communications
register. A weak pull-up to DVDD is provided on the DIN input.
25
DGND
Ground Reference Point for the Digital Circuitry.
26
DVDD
Digital Supply Voltage, 3 V or 5 V Nominal.
27
XTAL2
Output from the 32 kHz Crystal Oscillator Inverter.
28
XTAL1
Input to the 32 kHz Crystal Oscillator Inverter.
相关PDF资料 |
PDF描述 |
|---|---|
| HA1-4902-2 | IC COMPARATOR QUAD PREC 16-DIP |
| LTC1417IGN#PBF | IC A/D CONV 14BIT SAMPLNG 16SSOP |
| AD7732BRUZ | IC ADC 24BIT 2-CH 28-TSSOP |
| LTC1418CG#PBF | IC A/D CONV 14BIT SRL&PAR 28SSOP |
| AD7574JNZ | IC ADC 8BIT CMOS 5V 18-DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7719BRUZ-REEL | 功能描述:IC ADC 16BIT 24BIT DUAL 28TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| AD7719BRUZ-REEL7 | 功能描述:IC ADC 16BIT 24BIT DUAL 28TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| AD7719BRZ | 功能描述:IC ADC 16BIT 24BIT DUAL 28SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| AD7720 | 制造商:AD 制造商全称:Analog Devices 功能描述:CMOS Sigma-Delta Modulator |
| AD7720BRU | 功能描述:IC MODULATOR SIGMA-DELTA 28TSSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
发布紧急采购，3分钟左右您将得到回复。