- 您现在的位置：买卖IC网 > PDF目录10667 > AD7719BRUZ (Analog Devices Inc)IC ADC 16BIT 24BIT DUAL 28-TSSOP PDF资料下载
参数资料
| 型号： | AD7719BRUZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 4/40页 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT 24BIT DUAL 28-TSSOP |
| 标准包装： | 50 |
| 位数： | 16/24 |
| 采样率（每秒）： | 105 |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 2 |
| 功率耗散（最大）： | 4.5mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 28-TSSOP |
| 包装： | 管件 |
| 输入数目和类型： | 3 个差分，单极；3 个差分，双极 |
| 产品目录页面： | 778 (CN2011-ZH PDF) |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
REV. A
AD7719
–12–
DUAL-CHANNEL ADC CIRCUIT INFORMATION
Overview
The AD7719 incorporates two independent
Σ- ADC channels
(main and auxiliary) with on-chip digital filtering intended for
the measurement of wide dynamic range, low frequency signals
such as those in weigh-scale, strain gage, pressure transducer, or
temperature measurement applications.
Main Channel
This channel is intended to convert the primary sensor input.
This channel can be operated in buffered or unbuffered mode, and
can be programmed to have one of eight input voltage ranges
from ±20 mV to ±2.56 V. This channel can be configured as
either two fully differential inputs (AIN1/AIN2 and AIN3/AIN4)
or three pseudodifferential input channels (AIN1/AIN4, AIN2/
AIN4, and AIN3/AIN4). Buffering the input channel means that
the part can accommodate significant source impedances on the
analog input and that R, C filtering (for noise rejection or RFI
reduction) can be placed on the analog inputs if required. Operat-
ing in unbuffered mode leads to lower power consumption in low
power applications, but care must be exercised in unbuffered mode
because source impedances can introduce gain errors. The main
ADC also features sensor burnout currents that can be switched
on and off. These currents can be used to check that a transducer
is still operational before attempting to take measurements.
The ADC employs a
Σ- conversion technique to realize up to
24 bits of no-missing-codes performance. The
Σ- modulator
converts the sampled input signal into a digital pulse train whose
duty cycle contains the digital information. A Sinc
3 programmable
low-pass filter is then employed to decimate the modulator output
data stream to give a valid data conversion result at program-
mable output rates from 5.35 Hz (186.77 ms) to 105.03 Hz
(9.52 ms). A chopping scheme is also employed to minimize
ADC channel offset errors. A block diagram of the main ADC
input channel is shown in Figure 4. The sampling frequency of
the modulator loop is many times higher than the bandwidth of
the input signal. The integrator in the modulator shapes the
quantization noise (which results from the analog-to-digital
conversion) so that the noise is pushed toward one-half of the
modulator frequency. The output of the
Σ- modulator feeds
directly into the digital filter. The digital filter then band-limits
the response to a frequency significantly lower than one-half of
the modulator frequency. In this manner, the 1-bit output of the
comparator is translated into a band-limited, low noise output
from the AD7719 ADC. The AD7719 filter is a low-pass, Sinc
3,
or (SIN(x)/x)
3 filter whose primary function is to remove the
quantization noise introduced at the modulator. The cutoff
frequency and decimated output data rate of the filter are pro-
grammable via the SF word loaded to the filter register.
A chopping scheme is employed where the complete signal chain is
chopped, resulting in excellent dc offset and offset drift specifi-
cations, and is extremely beneficial in applications where drift, noise
rejection, and optimum EMI rejection are important factors.
With chopping, the ADC repeatedly reverses its inputs. The
decimated digital output words from the Sinc
3 filters therefore
have a positive offset and negative offset term included. As a result,
a final summing stage is included so that each output word from
the filter is summed and averaged with the previous filter output
to produce a new valid output result to be written to the ADC
data register.
Auxiliary Channel
The Auxiliary (Aux) channel is intended to convert supplementary
inputs such as those from a cold junction diode or thermistor.
This channel is unbuffered and has an input range of ±REFIN2
or ±REFIN2/2, determined by the ARN bit in the auxiliary ADC
control register (AD1CON). AIN3 and AIN4 can be multiplexed
into the auxiliary channel as single-ended inputs with respect to
AGND, while AIN5 and AIN6 can operate as a differential
input pair. With AIN6 tied to AGND, AIN5 can be operated as
an additional single-ended input. A block diagram of the auxiliary
ADC channel is shown in Figure 5.
SINC3 FILTER
MUX
BUF
PGA
MOD0
XOR
ANALOG
INPUT
DIGITAL
OUTPUT
1
8
SF
3
(
)
(8
SF )
3
1
2
AIN + VOS
AIN – VOS
f
CHOP
f
IN
f
MOD
f
CHOP
f
ADC
-
Figure 4. Main ADC Channel Block Diagram
OSCILLATOR
AVDD = DVDD = 5V
TA = 25 C
TIME BASE = 100ms/DIV
TRACE 1 = TRACE 2 = 2V/DIV
VDD
TPC 7. Typical Oscillator Power-Up
相关PDF资料 |
PDF描述 |
|---|---|
| HA1-4902-2 | IC COMPARATOR QUAD PREC 16-DIP |
| LTC1417IGN#PBF | IC A/D CONV 14BIT SAMPLNG 16SSOP |
| AD7732BRUZ | IC ADC 24BIT 2-CH 28-TSSOP |
| LTC1418CG#PBF | IC A/D CONV 14BIT SRL&PAR 28SSOP |
| AD7574JNZ | IC ADC 8BIT CMOS 5V 18-DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7719BRUZ-REEL | 功能描述:IC ADC 16BIT 24BIT DUAL 28TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| AD7719BRUZ-REEL7 | 功能描述:IC ADC 16BIT 24BIT DUAL 28TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| AD7719BRZ | 功能描述:IC ADC 16BIT 24BIT DUAL 28SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| AD7720 | 制造商:AD 制造商全称:Analog Devices 功能描述:CMOS Sigma-Delta Modulator |
| AD7720BRU | 功能描述:IC MODULATOR SIGMA-DELTA 28TSSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
发布紧急采购，3分钟左右您将得到回复。