参数资料
| 型号： | AD7793BRU |
| 厂商： | Analog Devices Inc |
| 文件页数： | 18/33页 |
| 文件大小： | 0K |
| 描述： | IC ADC 24BIT 3CH LP 16-TSSOP |
| 设计资源： | Fully Isolated Input Module Based on AD7793 and ADuM5401(CN0066) Fully Isolated Input Module Based on AD7793, ADuM5401, and a High Performance In-Amp (CN0067) |
| 标准包装： | 1 |
| 位数： | 24 |
| 采样率（每秒）： | 500 |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 2.5mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-TSSOP |
| 包装： | 管件 |
| 输入数目和类型： | 3 个差分，单极；3 个差分，双极 |
| 配用： | EVAL-AD7793EBZ-ND - BOARD EVALUATION FOR AD7793 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
AD7792/AD7793
Rev. B | Page 24 of 32
CIRCUIT DESCRIPTION
ANALOG INPUT CHANNEL
The AD7792/AD7793 have three differential analog input
channels. These are connected to the on-chip buffer amplifier
when the device is operated in buffered mode and directly to
the modulator when the device is operated in unbuffered mode.
In buffered mode (the BUF bit in the mode register is set to 1),
the input channel feeds into a high impedance input stage of the
buffer amplifier. Therefore, the input can tolerate significant
source impedances and is tailored for direct connection to
external resistive-type sensors, such as strain gauges or
resistance temperature detectors (RTDs).
When BUF = 0, the part is operated in unbuffered mode.
This results in a higher analog input current. Note that this
unbuffered input path provides a dynamic load to the driving
source. Therefore, resistor/capacitor combinations on the input
pins can cause gain errors, depending on the output impedance
of the source that is driving the ADC input. Table 19 shows the
allowable external resistance/capacitance values for unbuffered
mode such that no gain error at the 20-bit level is introduced.
Table 19. External R-C Combination for No 20-Bit Gain Error
C (pF)
R (Ω)
50
9 k
100
6 k
500
1.5 k
1000
900
5000
200
The AD7792/AD7793 can be operated in unbuffered mode only
when the gain equals 1 or 2. At higher gains, the buffer is auto-
matically enabled. The absolute input voltage range in buffered
mode is restricted to a range between GND + 100 mV and
AVDD – 100 mV. When the gain is set to 4 or higher, the in-amp
is enabled. The absolute input voltage range when the in-amp is
active is restricted to a range between GND + 300 mV and
AVDD 1.1 V. Take care in setting up the common-mode
voltage so that these limits are not exceeded to avoid
degradation in linearity and noise performance.
The absolute input voltage in unbuffered mode includes the
range between GND – 30 mV and AVDD + 30 mV as a result of
being unbuffered. The negative absolute input voltage limit does
allow the possibility of monitoring small true bipolar signals
with respect to GND.
INSTRUMENTATION AMPLIFIER
Amplifying the analog input signal by a gain of 1 or 2 is
performed digitally within the AD7792/AD7793. However,
when the gain equals 4 or higher, the output from the buffer is
applied to the input of the on-chip instrumentation amplifier.
This low noise in-amp means that signals of small amplitude
can be gained within the AD7792/AD7793 while still
maintaining excellent noise performance.
For example, when the gain is set to 64, the rms noise is 40 nV
typically, which is equivalent to 21 bits effective resolution or
18.5 bits peak-to-peak resolution.
The AD7792/AD7793 can be programmed to have a gain of 1,
2, 4, 8, 16, 32, 64, and 128 using Bit G2 to Bit G0 in the configu-
ration register. Therefore, with an external 2.5 V reference, the
unipolar ranges are from 0 mV to 20 mV to 0 V to 2.5 V while
the bipolar ranges are from ±20 mV to ±2.5 V. When the
in-amp is active (gain ≥ 4), the common-mode voltage (AIN(+)
+ AIN(–))/2 must be greater than or equal to 0.5 V.
If the AD7792/AD7793 are operated with an external reference
that has a value equal to AVDD, the analog input signal must be
limited to 90% of VREF/gain when the in-amp is active, for
correct operation.
BIPOLAR/UNIPOLAR CONFIGURATION
The analog input to the AD7792/AD7793 can accept either
unipolar or bipolar input voltage ranges. A bipolar input range
does not imply that the part can tolerate negative voltages with
respect to system GND. Unipolar and bipolar signals on the
AIN(+) input are referenced to the voltage on the AIN(–) input.
For example, if AIN() is 2.5 V, and the ADC is configured for
unipolar mode and a gain of 1, the input voltage range on the
AIN(+) pin is 2.5 V to 5 V.
If the ADC is configured for bipolar mode, the analog input
range on the AIN(+) input is 0 V to 5 V. The bipolar/unipolar
option is chosen by programming the U/B bit in the configura-
tion register.
DATA OUTPUT CODING
When the ADC is configured for unipolar operation, the output
code is natural (straight) binary with a zero differential input
voltage resulting in a code of 00...00, a midscale voltage
resulting in a code of 100...000, and a full-scale input voltage
resulting in a code of 111...111. The output code for any analog
input voltage can be represented as
Code = (2N × AIN × GAIN)/VREF
When the ADC is configured for bipolar operation, the output
code is offset binary with a negative full-scale voltage resulting
in a code of 000...000, a zero differential input voltage resulting
in a code of 100...000, and a positive full-scale input voltage
resulting in a code of 111...111. The output code for any analog
input voltage can be represented as
Code = 2N – 1 × [(AIN × GAIN /VREF) + 1]
where AIN is the analog input voltage, GAIN is the in-amp
setting (1 to 128), and N = 16 for the AD7792 and N = 24 for
the AD7793.
相关PDF资料 |
PDF描述 |
|---|---|
| AD7794BRU | IC ADC 24BIT 6CH LP 24-TSSOP |
| AD7797BRUZ-REEL | IC ADC 24BIT SIG-DEL 1CH 16TSSOP |
| AD7799BRU | IC ADC 24BIT 3CH LP 16-TSSOP |
| AD7801BRU | IC DAC 8BIT PARALLEL INP 20TSSOP |
| AD7810YR | IC ADC 10BIT 2.7V 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7793BRU-REEL | 制造商:Analog Devices 功能描述:ADC Single Delta-Sigma 470sps 24-bit Serial 16-Pin TSSOP T/R 制造商:Analog Devices 功能描述:ADC SGL DELTA-SIGMA 0.47KSPS 24BIT SERL 16TSSOP - Tape and Reel |
| AD7793BRUZ | 功能描述:IC ADC 24BIT SIG-DEL 3CH 16TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| AD7793BRUZ1 | 制造商:AD 制造商全称:Analog Devices 功能描述:3-Channel, Low Noise, Low Power, 16-/24-Bit ?￡-?? ADC with On-Chip In-Amp and Reference |
| AD7793BRUZ-REEL | 功能描述:IC ADC 24BIT 3CH LP 16-TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD7793BRUZ-REEL1 | 制造商:AD 制造商全称:Analog Devices 功能描述:3-Channel, Low Noise, Low Power, 16-/24-Bit ?￡-?? ADC with On-Chip In-Amp and Reference |
发布紧急采购，3分钟左右您将得到回复。