参数资料
| 型号： | AD7793BRU |
| 厂商： | Analog Devices Inc |
| 文件页数： | 7/33页 |
| 文件大小： | 0K |
| 描述： | IC ADC 24BIT 3CH LP 16-TSSOP |
| 设计资源： | Fully Isolated Input Module Based on AD7793 and ADuM5401(CN0066) Fully Isolated Input Module Based on AD7793, ADuM5401, and a High Performance In-Amp (CN0067) |
| 标准包装： | 1 |
| 位数： | 24 |
| 采样率（每秒）： | 500 |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 2.5mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-TSSOP |
| 包装： | 管件 |
| 输入数目和类型： | 3 个差分，单极；3 个差分，双极 |
| 配用： | EVAL-AD7793EBZ-ND - BOARD EVALUATION FOR AD7793 |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
AD7792/AD7793
Rev. B | Page 14 of 32
ON-CHIP REGISTERS
The ADC is controlled and configured via a number of on-chip
registers, which are described on the following pages. In the
following descriptions, set implies a Logic 1 state and cleared
implies a Logic 0 state, unless otherwise stated.
COMMUNICATIONS REGISTER
RS2, RS1, RS0 = 0, 0, 0
The communications register is an 8-bit write-only register. All
communications to the part must start with a write operation to
the communications register. The data written to the
communications register determines whether the next
operation is a read or write operation, and to which register this
operation takes place. For read or write operations, once the
subsequent read or write operation to the selected register is
complete, the interface returns to where it expects a write
operation to the communications register. This is the default
state of the interface and, on power-up or after a reset, the ADC
is in this default state waiting for a write operation to the
communications register. In situations where the interface
sequence is lost, a write operation of at least 32 serial clock
cycles with DIN high returns the ADC to this default state by
resetting the entire part. Table 11 outlines the bit designations
for the communications register. CR0 through CR7 indicate the
bit location, CR denoting the bits are in the communications
register. CR7 denotes the first bit of the data stream. The
number in parentheses indicates the power-on/reset default
status of that bit.
CR7
CR6
CR5
CR4
CR3
CR2
CR1
CR0
WEN(0)
R/W(0)
RS2(0)
RS1(0)
RS0(0)
CREAD(0)
0(0)
Table 11. Communications Register Bit Designations
Bit Location
Bit Name
Description
CR7
WEN
Write Enable Bit. A 0 must be written to this bit so that the write to the communications register actually
occurs. If a 1 is the first bit written, the part does not clock on to subsequent bits in the register. It stays at this
bit location until a 0 is written to this bit. Once a 0 is written to the WEN bit, the next seven bits are loaded to
the communications register.
CR6
R/W
A 0 in this bit location indicates that the next operation is a write to a specified register. A 1 in this position
indicates that the next operation is a read from the designated register.
CR5 to CR3
RS2 to
RS0
Register Address Bits. These address bits are used to select which of the ADC’s registers are being selected
during this serial interface communication. See Table 12.
CR2
CREAD
Continuous Read of the Data Register. When this bit is set to 1 (and the data register is selected), the serial
interface is configured so that the data register can be continuously read. For example, the contents of the
data register are placed on the DOUT pin automatically when the SCLK pulses are applied after the RDY pin
goes low to indicate that a conversion is complete. The communications register does not have to be written
to for data reads. To enable continuous read mode, the instruction 01011100 must be written to the
communications register. To exit the continuous read mode, the instruction 01011000 must be written to the
communications register while the RDY pin is low. While in continuous read mode, the ADC monitors activity
on the DIN line so that it can receive the instruction to exit continuous read mode. Additionally, a reset occurs
if 32 consecutive 1s are seen on DIN. Therefore, DIN should be held low in continuous read mode until an
instruction is to be written to the device.
CR1 to CR0
0
These bits must be programmed to Logic 0 for correct operation.
Table 12. Register Selection
RS2
RS1
RS0
Register
Register Size
0
Communications Register During a Write Operation
8-bit
0
Status Register During a Read Operation
8-bit
0
1
Mode Register
16-bit
0
1
0
Configuration Register
16-bit
0
1
Data Register
16-/24-bit
1
0
ID Register
8-bit
1
0
1
IO Register
8-bit
1
0
Offset Register
16-bit (AD7792)/24-bit (AD7793)
1
Full-Scale Register
16-bit (AD7792)/24-bit (AD7793)
相关PDF资料 |
PDF描述 |
|---|---|
| AD7794BRU | IC ADC 24BIT 6CH LP 24-TSSOP |
| AD7797BRUZ-REEL | IC ADC 24BIT SIG-DEL 1CH 16TSSOP |
| AD7799BRU | IC ADC 24BIT 3CH LP 16-TSSOP |
| AD7801BRU | IC DAC 8BIT PARALLEL INP 20TSSOP |
| AD7810YR | IC ADC 10BIT 2.7V 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7793BRU-REEL | 制造商:Analog Devices 功能描述:ADC Single Delta-Sigma 470sps 24-bit Serial 16-Pin TSSOP T/R 制造商:Analog Devices 功能描述:ADC SGL DELTA-SIGMA 0.47KSPS 24BIT SERL 16TSSOP - Tape and Reel |
| AD7793BRUZ | 功能描述:IC ADC 24BIT SIG-DEL 3CH 16TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| AD7793BRUZ1 | 制造商:AD 制造商全称:Analog Devices 功能描述:3-Channel, Low Noise, Low Power, 16-/24-Bit ?￡-?? ADC with On-Chip In-Amp and Reference |
| AD7793BRUZ-REEL | 功能描述:IC ADC 24BIT 3CH LP 16-TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD7793BRUZ-REEL1 | 制造商:AD 制造商全称:Analog Devices 功能描述:3-Channel, Low Noise, Low Power, 16-/24-Bit ?￡-?? ADC with On-Chip In-Amp and Reference |
发布紧急采购，3分钟左右您将得到回复。