参数资料
| 型号： | AD8155ACPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 18/36页 |
| 文件大小： | 0K |
| 描述： | IC MUX/DEMUX DUAL BUFFER 64LFCSP |
| 标准包装： | 1 |
| 系列： | XStream™ |
| 功能： | 多路复用器/多路分解器 |
| 电路： | 2 x 2:1 |
| 电压电源： | 单电源 |
| 电压 - 电源，单路/双路(±)： | 1.6 V ~ 3.6 V |
| 电流 - 电源： | 735mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 64-LFCSP-VQ（9x9） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
AD8155
Rev. 0 | Page 25 of 36
I2C INTERFACE DATA TRANSFERS: DATA READ
To read data from the AD8155 register set, a microcontroller or
any other I2C master must send the appropriate control signals
to the AD8155 slave device. The following steps must be taken,
where the signals are controlled by the I2C master, unless other-
wise specified. For a diagram of the procedure, see Figure 42.
1.
Send a start condition (while holding the SCL line high,
pull the SDA line low).
2.
Send the AD8155 part address (seven bits) whose upper
four bits are the static value b1010 and whose lower three
bits are controlled by the I2C_A[2:0] input pins. This
transfer should be MSB first.
3.
Send the write indicator bit (0).
4.
Wait for the AD8155 to acknowledge the request.
5.
Send the register address (eight bits) from which data is to
be read. This transfer should be MSB first. The register
address is kept in memory in the AD8155 until the part is
reset or the register address is written over with the same
procedure (Step 1 to Step 6).
6.
Wait for the AD8155 to acknowledge the request.
7.
Send a repeated start condition (while holding the SCL line
high, pull the SDA line low).
8.
Send the AD8155 part address (seven bits) whose upper
four bits are the static value b1010 and whose lower three
bits are controlled by the I2C_A[2:0] input pins. This
transfer should be MSB first.
9.
Send the read indicator bit (1).
10. Wait for the AD8155 to acknowledge the request.
11. The AD8155 then serially transfers the data (eight bits)
held in the register indicated by the address set in Step 5.
12. Acknowledge the data.
13. Do one or more of the following:
a.
Send a stop condition (while holding the SCL line high,
pull the SDA line high) and release control of the bus.
b.
Send a repeated start condition (while holding the
SCL line high, pull the SDA line low) and continue
with Step 2 of the write procedure (see the I2C
Interface Data Transfers: Data Write section) to
perform a write.
c.
Send a repeated start condition (while holding the
SCL line high, pull the SDA line low) and continue
with Step 2 of this procedure to perform a read from
another address.
d.
Send a repeated start condition (while holding the
SCL line high, pull the SDA line low) and continue
with Step 8 of this procedure to perform a read from
the same address.
In Figure 42, the AD8155 read process is shown. The SCL signal is
shown along with a general read operation and a specific example.
In this example, the value 0x49 is read from Address 0x6D of
an AD8155 device with a 0x53 part address. The part address
is seven bits wide and is composed of the AD8155 static upper
four bits (b1010) and the pin-programmable lower three bits
(I2C_A[2:0]). The address pins are set to b011. In Figure 42, the
corresponding step number is visible in the circle under the
waveform. The SCL line is driven by the I2C master and never
by the AD8155 slave. As for the SDA line, the data in the shaded
polygons is driven by the AD8155, whereas the data in the
nonshaded polygons is driven by the I2C master. The end phase
case shown is that of Step 13a.
It is important to note that the SDA line changes only when
the SCL line is low, except for the case of sending a start, stop,
or repeated start condition, as in Step 1, Step 7, and Step 13.
In Figure 42, A is the same as ACK. Equally, Sr represents a
repeated start where the SDA line is brought high before SCL
is raised. SDA is then dropped while SCL is still high.
SCL
SD
b1010
A
A Sr
DATA
A
STOP
REGISTER ADDR
START
ADDR
[2:0]
ADDR
[2:0]
b1010
R/
W
A
R/
W
A
SDA
1
2
3
4
5
6
7
8
9
10
11
12
13a
0
82
62
-04
3
Figure 42. I2C Read Diagram
相关PDF资料 |
PDF描述 |
|---|---|
| AD8156ABCZ | IC SWITCH XPT 4X4 W/EQ 49CSPBGA |
| AD8158ACPZ | IC MUX/DEMUX QUAD 2X1 100LFCSP |
| AD8159ASVZ | IC MUX/DEMUX QUAD BUFF 100TQFP |
| AD8174ANZ | IC MUX SW W/AMP 250MHZ 14-DIP |
| AD8175ABPZ | IC CROSSPOINT SWITCH TRPL 676BGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8155ACPZ-R7 | 功能描述:IC MUX/DEMUX DUAL BUFFER 64LFCSP RoHS:是 类别:集成电路 (IC) >> 接口 - 模拟开关，多路复用器，多路分解器 系列:XStream™ 其它有关文件:STG4159 View All Specifications 标准包装:5,000 系列:- 功能:开关 电路:1 x SPDT 导通状态电阻:300 毫欧 电压电源:双电源 电压 - 电源，单路/双路(±):±1.65 V ~ 4.8 V 电流 - 电源:50nA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:7-WFBGA，FCBGA 供应商设备封装:7-覆晶 包装:带卷 (TR) |
| AD8155-EVALZ | 制造商:AD 制造商全称:Analog Devices 功能描述:6.5 Gbps Dual Buffer Mux/Demux |
| AD8155XCPZ | 制造商:Analog Devices 功能描述: |
| AD8156 | 制造商:AD 制造商全称:Analog Devices 功能描述:6.25 Gbps 4】4 Digital Crosspoint Switch with EQ |
| AD8156ABCZ | 功能描述:IC SWITCH XPT 4X4 W/EQ 49CSPBGA RoHS:是 类别:集成电路 (IC) >> 接口 - 专用 系列:XStream™ 特色产品:NXP - I2C Interface 标准包装:1 系列:- 应用:2 通道 I²C 多路复用器 接口:I²C，SM 总线 电源电压:2.3 V ~ 5.5 V 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:剪切带 (CT) 安装类型:表面贴装 产品目录页面:825 (CN2011-ZH PDF) 其它名称:568-1854-1 |
发布紧急采购，3分钟左右您将得到回复。