参数资料
| 型号： | AD8155ACPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 24/36页 |
| 文件大小： | 0K |
| 描述： | IC MUX/DEMUX DUAL BUFFER 64LFCSP |
| 标准包装： | 1 |
| 系列： | XStream™ |
| 功能： | 多路复用器/多路分解器 |
| 电路： | 2 x 2:1 |
| 电压电源： | 单电源 |
| 电压 - 电源，单路/双路(±)： | 1.6 V ~ 3.6 V |
| 电流 - 电源： | 735mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 64-LFCSP-VQ（9x9） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
AD8155
Rev. 0 | Page 30 of 36
SUPPLY SEQUENCING
Ideally, all power supplies should be brought up to the appropri-
ate levels simultaneously (power supply requirements are set by
the supply limits in Table 1 and the absolute maximum ratings
listed in Table 3). In the event that the power supplies to the
AD8155 are brought up separately, the supply power-up sequence
is as follows: DVCC is powered first, followed by VCC, and lastly
VTTI and VTTO. The power-down sequence is reversed, with VTTI
and VTTO being powered off first.
VTTI and VTTO contain ESD protection diodes to the VCC power
current condition in these devices (ISUSTAINED < 64 mA), the VTTI
and VTTO supplies should be powered on after VCC and should
be powered off before VCC.
If the system power supplies have a high impedance in the
powered off state, then supply sequencing is not required
provided the following limits are observed:
Peak current from VTTI or VTTO to VCC < 200 mA
Sustained current from VTTI or VTTO to VCC < 64 mA
SINGLE SUPPLY vs. MULTIPLE SUPPLY
OPERATION
The AD8155 supports a flexible supply voltage of 1.8 V to 3.3 V.
For some dc-coupled links, 1.2 V or ground-referenced signaling
may be desired. In these cases, the AD8155 can be run with a
split supply configuration. An example is shown in Figure 47.
TX
RX
0V
VTTO
VCC
DVCC
50
VTTI
CML
AD8155
Z0
VEE = –3.3V (OR –1.8V)
VOH = 0mV
VOL = –400mV
Z0
+
–
MCU
MCU_VSS
TO AD8155
I2C_SDA
VEE
ADuM1250
MCU_VDD
DVCC
I2C_SCL
08
26
2-
04
8
Figure 47. Multiple Supply Operation
Table 21. Alternate Supply Configuration Examples
Signal Level
VCC, VTTI, VTTO
VEE
1.2 V CML
1.2 V
2.1 V ≤VEE ≤ 0.6 V
GND 400 mV diff
GND
3.3 V ≤VEE ≤ 1.8 V
The AD8155 control signals are always referenced between
DVCC and VEE and, when using a split supply configuration,
logic level-shift circuits should be used. The evaluation board
design shows the use of the Analog Devices, Inc., ADUM1250
I2C isolator and a level shifter to level-shift the SCL and SDA
signals (for information about the evaluation board, see the
Evaluation of DC-Coupled Links
When evaluating the AD8155 dc-coupled, note that most lab
equipment is ground referenced whereas the AD8155 high
speed I/O are connected by 50 Ω on-die termination resistors to
VTTI and VTTO. To interface the AD8155 to ground-referenced,
high speed instrumentation (for example, the 50 Ω inputs of a
high speed oscilloscope), it is necessary to level-shift the outputs by
either using a dc-blocking network or powering the AD8155
between ground and a negative supply.
For example, to evaluate 1.8 V dc-coupled transmitter perfor-
mance with a 50 Ω ground-referenced oscilloscope, use the
following supply configuration:
VCC = VTTO = VTTI = Ground
VEE = 1.8 V
Ground < DVCC < 1.5 V
INITIALIZATION SEQUENCE FOR LOW POWER
AND LOS_INT OPERATION
The following programming sequence is required to initialize
the device in a low power mode and to enable the LOS_INT:
set the reserved bits to Logic 1 in the RX and TX control
registers by writing the value 0x0C to the 0x40, 0x48, 0x80,
0x88, 0xC0, and 0xC8 registers.
相关PDF资料 |
PDF描述 |
|---|---|
| AD8156ABCZ | IC SWITCH XPT 4X4 W/EQ 49CSPBGA |
| AD8158ACPZ | IC MUX/DEMUX QUAD 2X1 100LFCSP |
| AD8159ASVZ | IC MUX/DEMUX QUAD BUFF 100TQFP |
| AD8174ANZ | IC MUX SW W/AMP 250MHZ 14-DIP |
| AD8175ABPZ | IC CROSSPOINT SWITCH TRPL 676BGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8155ACPZ-R7 | 功能描述:IC MUX/DEMUX DUAL BUFFER 64LFCSP RoHS:是 类别:集成电路 (IC) >> 接口 - 模拟开关，多路复用器，多路分解器 系列:XStream™ 其它有关文件:STG4159 View All Specifications 标准包装:5,000 系列:- 功能:开关 电路:1 x SPDT 导通状态电阻:300 毫欧 电压电源:双电源 电压 - 电源，单路/双路(±):±1.65 V ~ 4.8 V 电流 - 电源:50nA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:7-WFBGA，FCBGA 供应商设备封装:7-覆晶 包装:带卷 (TR) |
| AD8155-EVALZ | 制造商:AD 制造商全称:Analog Devices 功能描述:6.5 Gbps Dual Buffer Mux/Demux |
| AD8155XCPZ | 制造商:Analog Devices 功能描述: |
| AD8156 | 制造商:AD 制造商全称:Analog Devices 功能描述:6.25 Gbps 4】4 Digital Crosspoint Switch with EQ |
| AD8156ABCZ | 功能描述:IC SWITCH XPT 4X4 W/EQ 49CSPBGA RoHS:是 类别:集成电路 (IC) >> 接口 - 专用 系列:XStream™ 特色产品:NXP - I2C Interface 标准包装:1 系列:- 应用:2 通道 I²C 多路复用器 接口:I²C，SM 总线 电源电压:2.3 V ~ 5.5 V 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:剪切带 (CT) 安装类型:表面贴装 产品目录页面:825 (CN2011-ZH PDF) 其它名称:568-1854-1 |
发布紧急采购，3分钟左右您将得到回复。