参数资料
| 型号： | AD9600ABCPZ-150 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 40/72页 |
| 文件大小： | 0K |
| 描述： | IC ADC 10BIT 150MSPS 64LFCSP |
| 标准包装： | 1 |
| 位数： | 10 |
| 采样率（每秒）： | 150M |
| 数据接口： | 串行，SPI? |
| 转换器数目： | 2 |
| 功率耗散（最大）： | 890mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 64-LFCSP-VQ（9x9） |
| 包装： | 托盘 |
| 输入数目和类型： | 4 个单端，单极；2 个差分，单极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页当前第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页
AD9600
Rev. B | Page 45 of 72
Increase Gain Dwell Time (Register 0x10A and
Register 0x10B)
Register 0x10A, Bits [7:0]—Increase Gain Dwell Time [7:0]
Register 0x10B, Bits [7:0]—Increase Gain Dwell Time [15:8]
These registers are programmed with the dwell time in ADC
clock cycles. The signal must be below the fine lower threshold
value before the increase gain (IG) indicator is asserted.
Signal Monitor DC Correction Control (Register 0x10C)
Bit 7—Reserved
Bit 6—DC Correction Freeze
When Bit 6 is set high, the dc correction is not updated to the
signal monitor block; therefore, the block continues to hold the last
dc value that it calculated.
Bits [5:2]—DC Correction Bandwidth
These bits set the averaging time of the power monitor dc
correction function. This 4-bit word sets the bandwidth of the
correction block according to the following equation:
π
×
=
2
_
14
CLK
k
f
BW
Corr
DC
where:
k is the 4-bit value programmed in Register 0x10C, Bits [5:2]
(values between 0 and 13 are valid for k; programming 14 or
15 provides the same result as programming 13).
fCLK is the AD9600 ADC sample rate in hertz.
Bit 1—DC Correction for Signal Path Enable
Setting Bit 1 high causes the output of the dc measurement block to
be summed with the data in the signal path to remove the dc offset
from the signal path.
Bit 0—DC Correction for Signal Monitor Enable
Bit 0 enables the dc correction function in the signal monitor block.
The dc correction is an averaging function that can be used by
the signal monitor to remove dc offset in the signal. Removing
this dc from the measurement allows a more accurate reading.
Signal Monitor DC Value Channel A (Register 0x10D and
Register 0x10E)
Register 0x10D, Bits [7:0]—DC Value Channel A [7:0]
Register 0x10E, Bits [7:6]—Reserved
Register 0x10E, Bits [5:0]—DC Value Channel A [13:8]
These read-only registers hold the latest dc offset value computed
by the signal monitor for Channel A.
Signal Monitor DC Value Channel B (Register 0x10F and
Register 0x110)
Register 0x10F Bits [7:0]—DC Value Channel B [7:0]
Register 0x110 Bits [7:6]—Reserved
Register 0x110 Bits [5:0]—DC Value Channel B [13:8]
These read-only registers hold the latest dc offset value computed
by the signal monitor for Channel B.
Signal Monitor SPORT Control (Register 0x111)
Bit 7—Reserved
Bit 6—RMS/MS Magnitude Output Enable
These bits enable the 20-bit rms or ms magnitude measurement
as output on the SPORT.
Bit 5—Peak Detector Output Enable
Bit 5 enables the 10-bit peak measurement as output on the SPORT.
Bit 4—Threshold Crossing Output Enable
Bit 4 enables the 10-bit threshold measurement as output on
the SPORT.
Bits [3:2]—SPORT SMI SCLK Divide
The values of these bits set the SPORT SMI SCLK divide ratio
from the input clock. A value of 0x01 sets divide by 2 (default),
a value of 0x10 sets divide by 4, and a value of 0x11 sets divide by 8.
Bit 1— SPORT SMI SCLK Sleep
Setting Bit 1 high causes the SMI SCLK to remain low when the
signal monitor block has no data to transfer.
Bit 0—Signal Monitor SPORT Output Enable
When set, Bit 0 enables the SPORT output of the signal monitor
to begin shifting out the result data from the signal monitor block.
Signal Monitor Control (Register 0x112)
Bit 7—Complex Power Calculation Mode Enable
This mode assumes that I data is present on one channel and
Q data is present on the opposite channel. The result reported
is the complex power, measured as
2
Q
I +
Bits [6:4]—Reserved
Bit 3—Signal Monitor RMS/MS Select
Setting Bit 3 low selects rms power measurement mode. Setting
Bit 3 high selects ms power measurement mode.
Bits [2:1]—Signal Monitor Mode
Bit 2 and Bit 1 set the mode of the signal monitor for the data
output of Register 0x116 to Register 0x11B. Setting Bit 2 and Bit 1
to 00 selects rms/ms magnitude output, setting these bits to 01
selects peak power output, and setting to 10 or 11 selects threshold
crossing output.
Bit 0—Signal Monitor Enable
Setting Bit 0 high enables the signal monitor block.
相关PDF资料 |
PDF描述 |
|---|---|
| AD9608BCPZRL7-125 | IC ADC 10BIT 125MSPS 64LFCSP |
| AD9609BCPZRL7-80 | IC ADC 10BIT SRL/SPI 80M 32LFCSP |
| AD9613BCPZ-170 | IC ADC 12BIT SRL 170MSPS 64LFCSP |
| AD9627ABCPZ-125 | IC ADC 12BIT 1255MSPS 64LFCSP |
| AD9627ABCPZ11-150 | IC ADC 11BIT 150MSPS 64LFCSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9600BCPZ-105 | 制造商:Analog Devices 功能描述:ADC Dual Pipelined 105Msps 10-bit Parallel/LVDS 64-Pin LFCSP EP |
| AD9600BCPZ-125 | 制造商:Analog Devices 功能描述:ADC Dual Pipelined 125Msps 10-bit Parallel/LVDS 64-Pin LFCSP EP |
| AD9600BCPZ-150 | 制造商:Analog Devices 功能描述: |
| AD9601 | 制造商:AD 制造商全称:Analog Devices 功能描述:10-Bit, 200 MSPS/250 MSPS 1.8 V Analog-to-Digital Converter |
| AD9601-250EBZ | 功能描述:数据转换 IC 开发工具 10-Bit 250 Msps LowPwr CMOS ADC RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
发布紧急采购，3分钟左右您将得到回复。