- 您现在的位置：买卖IC网 > PDF目录22107 > ADM1075-2ACPZ (Analog Devices Inc)IC HOT SWAP CTRLR -48V 28LFCSP PDF资料下载
参数资料
| 型号： | ADM1075-2ACPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 28/52页 |
| 文件大小： | 0K |
| 描述： | IC HOT SWAP CTRLR -48V 28LFCSP |
| 标准包装： | 1 |
| 类型： | 热交换控制器 |
| 应用： | -48V 远程电力系统，高可用性，电信/数据通信系统 |
| 内部开关： | 无 |
| 电流限制： | 可调 |
| 电源电压： | -35 V ~ -80 V |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-WFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 28-LFCSP-WQ（5x5） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
ADM1075
PMBus INTERFACE
The I 2 C bus is a common, simple serial bus used by many devices
to communicate. It defines the electrical specifications, the bus
timing, the physical layer, and some basic protocol rules.
SMBus is based on I 2 C and aims to provide a more robust and
fault-tolerant bus. Functions such as bus timeout and packet
error checking are added to help achieve this robustness, along
with more specific definitions of the bus messages used to read
and write data to devices on the bus.
PMBus is layered on top of SMBus and, in turn, on I 2 C. Using the
SMBus defined bus messages, PMBus defines a set of standard
commands that can be used to control a device that is part of a
power chain.
The ADM1075 command set is based upon the PMBus? Power
System Management Protocol Specification , Part I and Part II,
Revision 1.2. This version of the standard is intended to provide
a common set of commands for communicating with dc-to-dc
type devices. However, many of the standard PMBus commands
can be mapped directly to the functions of a hot swap controller.
Part I and Part II of the PMBus standard describe the basic
commands and how they can be used in a typical PMBus setup.
The following sections describe how the PMBus standard and
the ADM1075 specific commands are used.
DEVICE ADDRESSING
The ADM1075 is available in two models: the ADM1075-1 and
upper five bits (MSBs) of the address word are fixed and are
different for each model, as follows:
The ADM1075-1 and ADM1075-2 have a single ADR pin that
is used to select one of four possible addresses for a given
model. The ADR pin connection selects the lowest two bits
Table 6. PMBus Addresses and ADR Pin Connection
Value of Address LSBs ADR Pin Connection
00 Connect to VEE
01 150 k? resistor to VEE
10 No connection (floating)
11 Connect to VCAP
Data Sheet
SMBus PROTOCOL USAGE
All I 2 C transactions on the ADM1075 are performed using
SMBus defined bus protocols. The following SMBus protocols
? Send byte
? Receive byte
? Write byte
? Read byte
? Write word
? Read word
? Block read
PACKET ERROR CHECKING
The ADM1075 PMBus interface supports the use of the packet
error checking (PEC) byte that is defined in the SMBus standard.
The PEC byte is transmitted by the ADM1075 during a read
transaction or sent by the bus host to the ADM1075 during a
write transaction. The ADM1075 supports the use of PEC with
all the SMBus protocols that it implements.
The use of the PEC byte is optional. The bus host can decide
whether to use the PEC byte with the ADM1075 on a message-
by-message basis. There is no need to enable or disable PEC in
The PEC byte is used by the bus host or the ADM1075 to detect
errors during a bus transaction, depending on whether the trans-
action is a read or a write. If the host determines that the PEC
byte read during a read transaction is incorrect, it can decide to
repeat the read if necessary. If the ADM1075 determines that the
PEC byte sent during a write transaction is incorrect, it ignores
the command (does not execute it) and sets a status flag.
Within a group command, the host can choose to send or not
PARTIAL TRANSACTIONS ON I 2 C BUS
In the event of a specific sequence of events occurring on the
I 2 C bus, it is possible for the I 2 C interface on the device to go
into a state where it fails to ACK the next I 2 C transaction directed
to it. There are two ways that this behavior can be triggered:
? A partial I 2 C transaction consisting of a start condition,
followed by a single SCL clock pulse and stop condition.
? If the I 2 C bus master does not follow the 300 ns SDA data
hold time when signaling the ACK/NACK bit at the end of
a transaction. The device sees this as a single SCL clock
partial transaction.
In the event that the device NACKs a transaction, then the I 2 C
interface on the device can be reset by sending a series of up to
16 SCL clock pulses, or performing a dummy transaction to
another I 2 C address on the bus.
Rev. C | Page 28 of 52
相关PDF资料 |
PDF描述 |
|---|---|
| VI-23B-EV-F3 | CONVERTER MOD DC/DC 95V 150W |
| TAP104M035DCS | CAP TANT 0.1UF 35V 20% RADIAL |
| TOP246FN | IC OFFLINE SWIT UVLO HV TO262 |
| ADM1275-1ACPZ | IC HOT SWAP CTRL PMBUS 20LFCSP |
| VI-23B-EV-F2 | CONVERTER MOD DC/DC 95V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1075-2ACPZ-RL7 | 功能描述:IC HOT SWAP CTRLR -48V 28LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| ADM1075-2ARUZ | 功能描述:IC CTRLR HOTSWAP -48V 28TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| ADM1075-2ARUZ-RL7 | 功能描述:IC HOTSWAP CTRLR -48V 28TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| ADM1085 | 制造商:AD 制造商全称:Analog Devices 功能描述:Simple Sequencers in 6-Lead SC70 |
| ADM1085AKS-REEL7 | 制造商:Rochester Electronics LLC 功能描述:SIMPLE SEQUENCER OPEN DRAIN EN IC - Tape and Reel 制造商:Analog Devices 功能描述:IC VOLTAGE SEQUENCER |
发布紧急采购，3分钟左右您将得到回复。