- 您现在的位置：买卖IC网 > PDF目录22107 > ADM1075-2ACPZ (Analog Devices Inc)IC HOT SWAP CTRLR -48V 28LFCSP PDF资料下载
参数资料
| 型号： | ADM1075-2ACPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 37/52页 |
| 文件大小： | 0K |
| 描述： | IC HOT SWAP CTRLR -48V 28LFCSP |
| 标准包装： | 1 |
| 类型： | 热交换控制器 |
| 应用： | -48V 远程电力系统，高可用性，电信/数据通信系统 |
| 内部开关： | 无 |
| 电流限制： | 可调 |
| 电源电压： | -35 V ~ -80 V |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-WFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 28-LFCSP-WQ（5x5） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页当前第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
Data Sheet
SMBus ALERT RESPONSE ADDRESS
The SMBus alert response address (ARA) is a special address
that can be used by the bus host to locate any devices that need
to talk to it. A host typically uses a hardware interrupt pin to
monitor the SMBus alert pins of a number of devices. When the
host interrupt occurs, the host issues a message on the bus using
the SMBus receive byte or receive byte with PEC protocol.
The special address used by the host is 0x0C. Any devices that
have an SMBAlert signal return their own 7-bit address as the
seven MSBs of the data byte. The LSB value is not used and can
be either 1 or 0. The host reads the device address from the
received data byte and proceeds to handle the alert condition.
More than one device may have an active SMBAlert signal and
attempt to communicate with the host. In this case, the device
with the lowest address dominates the bus and succeeds in
transmitting its address to the host. The device that succeeds
disables its SMBusAlert signal. If the host sees that the SMBus
alert signal is still low, it continues to read addresses until all
devices that need to talk to it have successfully transmitted their
addresses.
EXAMPLE USE OF SMBus ALERT RESPONSE
ADDRESS
The full sequence of steps that occurs when an SMBAlert is
generated and cleared is as follows:
1. A fault or warning is enabled using the ALERT1_CONFIG
command, and the corresponding status bit for the fault or
warning goes from 0 to 1, indicating that the fault/warning
has just become active.
2. The GPO1/ALERT1/CONV or GPO2/ALERT2 pin
becomes active (low) to signal that an SMBAlert is active.
ADM1075
3. The host processor issues an SMBus alert response address
to determine which device has an active alert.
4. If there are no other active alerts from devices with lower
I 2 C addresses, this device makes the GPO1/ALERT1/CONV
or GPO2/ALERT2 pin inactive (high) during the NACK
bit period after it sends its address to the host processor.
5. If the GPO1/ALERT1/CONV or GPO2/ALERT2 pin stays
low, the host processor must continue to issue SMBus alert
response address commands to devices to find out the
addresses of all devices whose status it must check.
6. The ADM1075 continues to operate with the GPO1/ALERT1/
CONV or GPO2/ALERT2 pin inactive and the contents of
the status bytes unchanged until the host reads the status
bytes and clears them, or until a new fault occurs. That is, if
a status bit for a fault/warning that is enabled on the
GPO1/ALERT1/CONV or GPO2/ALERT2 pin and that
was not already active (equal to 1) goes from 0 to 1, a new
alert is generated, causing the GPO1/ALERT1/CONV or
GPO2/ALERT2 pin to become active again.
DIGITAL COMPARATOR MODE
The GPO1/ALERT1/CONV and GPO2/ALERT2 pins can be
configured to indicate if a user defined threshold for voltage,
current, or power is being exceeded. In this mode, the output
pin is live and is not latched when a warning threshold is
exceeded. In effect, the pin acts as a digital comparator where
the threshold is set using the warning limit threshold commands.
The ALERTx_CONFIG command is used, as for the SMBAlert
configuration, to select the specific warning threshold to be
monitored. The GPO1/ALERT1/CONV or GPO2/ALERT2 pin
then indicates if the measured value is above or below the
threshold.
Rev. C | Page 37 of 52
相关PDF资料 |
PDF描述 |
|---|---|
| VI-23B-EV-F3 | CONVERTER MOD DC/DC 95V 150W |
| TAP104M035DCS | CAP TANT 0.1UF 35V 20% RADIAL |
| TOP246FN | IC OFFLINE SWIT UVLO HV TO262 |
| ADM1275-1ACPZ | IC HOT SWAP CTRL PMBUS 20LFCSP |
| VI-23B-EV-F2 | CONVERTER MOD DC/DC 95V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1075-2ACPZ-RL7 | 功能描述:IC HOT SWAP CTRLR -48V 28LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| ADM1075-2ARUZ | 功能描述:IC CTRLR HOTSWAP -48V 28TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| ADM1075-2ARUZ-RL7 | 功能描述:IC HOTSWAP CTRLR -48V 28TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| ADM1085 | 制造商:AD 制造商全称:Analog Devices 功能描述:Simple Sequencers in 6-Lead SC70 |
| ADM1085AKS-REEL7 | 制造商:Rochester Electronics LLC 功能描述:SIMPLE SEQUENCER OPEN DRAIN EN IC - Tape and Reel 制造商:Analog Devices 功能描述:IC VOLTAGE SEQUENCER |
发布紧急采购，3分钟左右您将得到回复。