- 您现在的位置：买卖IC网 > PDF目录22107 > ADM1075-2ACPZ (Analog Devices Inc)IC HOT SWAP CTRLR -48V 28LFCSP PDF资料下载
参数资料
| 型号： | ADM1075-2ACPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 31/52页 |
| 文件大小： | 0K |
| 描述： | IC HOT SWAP CTRLR -48V 28LFCSP |
| 标准包装： | 1 |
| 类型： | 热交换控制器 |
| 应用： | -48V 远程电力系统，高可用性，电信/数据通信系统 |
| 内部开关： | 无 |
| 电流限制： | 可调 |
| 电源电压： | -35 V ~ -80 V |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-WFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 28-LFCSP-WQ（5x5） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页当前第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
Data Sheet
HOT SWAP CONTROL COMMANDS
OPERATION Command
The GATE pin that drives the FET is controlled by a dedicated
hot swap state machine. The UVH, UVL, and OV input pins,
along with the TIMER and SS pins and the current sense, all
feed into the state machine and control when and how strongly
the gate is turned off.
It is also possible to control the hot swap GATE output using
commands over the PMBus interface. The OPERATION com-
mand can be used to request the hot swap output to turn on.
However, if the UV pin indicates that the input supply is less
than required, the hot swap output is not turned on, even if the
OPERATION command indicates that the output should be
enabled.
If the OPERATION command is used to disable the hot swap
output, the GATE pin is held low, even if all hot swap state
machine control inputs indicate that it can be enabled.
The default state of the OPERATION command ON bit is 1;
therefore, the hot swap output is always enabled when the
ADM1075 comes out of UVLO. If the ON bit is never changed,
the UV input is the hot swap master on/off control signal.
By default, at power-up, the OPERATION command is disabled
and must be enabled using the DEVICE_CONFIG command.
This prevents inadvertent shutdowns of the hot swap controller
by software.
If the ON bit is set to 0 while the UV signal is high, the hot swap
output is turned off. If the UV signal is low or if the OV signal is
high, the hot swap output is already off and the status of the ON
bit has no effect.
If the ON bit is set to 1, the hot swap output is requested to turn
on. If the UV signal is low or if the OV signal is high, setting the
ON bit to 1 has no effect, and the hot swap output remains off.
It is possible to determine at any time whether the hot swap output
is enabled using the STATUS_BYTE or the STATUS_WORD
command (see the Status Commands section).
The OPERATION command can also be used to clear any latched
faults in the status registers. To clear latched faults, set the ON
bit to 0, and then reset it to 1.
DEVICE_CONFIG Command
The DEVICE_CONFIG command is used to configure certain
settings within the ADM1075 , for example, to modify the
duration of the severe overcurrent glitch filter and to set the trip
threshold. This command is also used to configure the polarity
of the second IOUT current warnings.
At power-up, the OPERATION command is disabled, and
the ADM1075 responds with a NACK if the OPERATION
command is received. To allow use of the OPERATION
command, the OPERATION_CMD_EN bit must be set
using the DEVICE_CONFIG command.
ADM1075
POWER_CYCLE Command
The POWER_CYCLE command can be used to request that
the ADM1075 be turned off for ~10 seconds and then back on.
This command can be useful if the processor that controls the
ADM1075 is also powered off when the part is turned off. This
command allows the processor to request that the ADM1075 turn
off and back on again as part of a single command.
ADM1075 INFORMATION COMMANDS
CAPABILITY Command
The CAPABILITY command can be used by host processors
The features reported are the maximum bus speed and whether
the device supports the packet error checking (PEC) byte and
the SMBAlert reporting function.
PMBUS_REVISION Command
The PMBUS_REVISION command reports the version of Part I
and Part II of the PMBus standard.
MFR_ID, MFR_MODEL, and MFR_REVISION Commands
The MFR_ID, MFR_MODEL, and MFR_REVISION
commands return ASCII strings that can be used to facilitate
detection and identification of the ADM1075 on the bus.
These commands are read using the SMBus block read message
type. This message type requires that the ADM1075 return a
byte count corresponding to the length of the string data that is
to be read back.
STATUS COMMANDS
The ADM1075 provides a number of status bits that are used
to report faults and warnings from the hot swap controller and
the power monitor. These status bits are located in six different
registers that are arranged in a hierarchy. The STATUS_BYTE
and STATUS_WORD commands provide eight bits and 16 bits
of high level information, respectively. The STATUS_BYTE and
STATUS_WORD commands contain the most important status
bits, as well as pointer bits that indicate whether any of the four
other status registers need to be read for more detailed status
information.
In the ADM1075 , a particular distinction is made between
faults and warnings. A fault is always generated by the hot swap
controller and is defined by hardware component values. Three
events can generate a fault.
? Overcurrent condition that causes the hot swap timer to
time out
? Overvoltage condition on the OV pin
? Undervoltage condition on the UVx pin
When a fault occurs, the hot swap controller always takes some
action, usually to turn off the GATE pin, which is driving the
FET. A fault can also generate an SMBAlert on one or both of
the GPOx/ALERTx pins.
Rev. C | Page 31 of 52
相关PDF资料 |
PDF描述 |
|---|---|
| VI-23B-EV-F3 | CONVERTER MOD DC/DC 95V 150W |
| TAP104M035DCS | CAP TANT 0.1UF 35V 20% RADIAL |
| TOP246FN | IC OFFLINE SWIT UVLO HV TO262 |
| ADM1275-1ACPZ | IC HOT SWAP CTRL PMBUS 20LFCSP |
| VI-23B-EV-F2 | CONVERTER MOD DC/DC 95V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1075-2ACPZ-RL7 | 功能描述:IC HOT SWAP CTRLR -48V 28LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| ADM1075-2ARUZ | 功能描述:IC CTRLR HOTSWAP -48V 28TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| ADM1075-2ARUZ-RL7 | 功能描述:IC HOTSWAP CTRLR -48V 28TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| ADM1085 | 制造商:AD 制造商全称:Analog Devices 功能描述:Simple Sequencers in 6-Lead SC70 |
| ADM1085AKS-REEL7 | 制造商:Rochester Electronics LLC 功能描述:SIMPLE SEQUENCER OPEN DRAIN EN IC - Tape and Reel 制造商:Analog Devices 功能描述:IC VOLTAGE SEQUENCER |
发布紧急采购，3分钟左右您将得到回复。