- 您现在的位置：买卖IC网 > PDF目录1776 > ADN8830ACPZ-REEL (Analog Devices Inc)IC THERMO COOLER CNTRLR 32-LFCSP PDF资料下载
参数资料
| 型号： | ADN8830ACPZ-REEL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 19/22页 |
| 文件大小： | 0K |
| 描述： | IC THERMO COOLER CNTRLR 32-LFCSP |
| 标准包装： | 1 |
| 应用： | 热电冷却器 |
| 电流 - 电源： | 8mA |
| 电源电压： | 3.3 V ~ 5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 32-LFCSP-VQ（5x5） |
| 包装： | 剪切带 (CT) |
| 其它名称： | ADN8830ACPZ-REELCT |
ADN8830
= C 1 × R 1
Power Supply Ripple
Minimizing ripple on the power supply voltage can be an impor-
tant consideration, particularly in signal source laser applications.
If the laser diode is operated from the same supply rail as the TEC
controller, ripple on the supply voltage could cause inadvertent
modulation of the laser frequency. As most laser diodes are driven
from a 5 V supply, it is recommended the ADN8830 be operated
from a separate 3.3 V regulated supply unless higher TEC voltages
are required. Operation from 3.3 V also improves efficiency, thus
minimizing power dissipation.
The power supply ripple is primarily a function of the supply by-
pass capacitance, also called bulk capacitance, and the inductor
ripple current. Similar to the L-C filter at the PWM amplifier
output, using more capacitance with low equivalent series resis-
tance (ESR) will lower the supply ripple. A larger inductor value
will reduce the inductor ripple current, but this may not be
practical in the application. A recommended approach is to use a
standard electrolytic capacitor in parallel with a low ESR capacitor.
A surface-mount 220 μ F electrolytic in parallel with a 22 μ F poly-
mer aluminum low ESR capacitor can occupy an approximate total
board area of only 0.94 square inches or 61 square millimeters.
Using these capacitors along with a 4.7 μ H inductor can yield a
supply ripple of less than 5 mV.
A 10 m Ω resistor placed in series with the PVDD supply line creates a
voltage drop proportional to the absolute value of the output current.
The AD8601 is a CMOS amplifier that is configured as a com-
parator. As long as the voltage at its inverting input (V S ) exceeds
the voltage set by the resistor divider at the noninverting input (V X ),
the gate of Q1 will remain at ground. This leaves Q1 on, effectively
connecting D1 to the positive rail and leaving the voltage on C1 at
V DD . Should enough current flow through R S to drop V S below V X ,
Q1 will turn off and C1 will discharge through R2 down to a logic
low to activate the ADN8830 shutdown. Once V S returns to a
voltage greater than V X , Q1 will turn back on and C1 will charge
back to V DD through R1. The shutdown and reactivation time
constants are approximately
SD = C 1 × R 1
(42)
ON
The shutdown time constant should be a minimum of 10 clock
cycles to ensure high current switching transients do not trigger a
false activation. If powered from 5 V, the circuit shown will shut
down the ADN8830 should PVDD deliver over 5 A for more than
1 ms. After shutdown, the circuit will reactivate the ADN8830 in
about 1 second.
The voltage drop across R S is found as
I OUT L S
R R
High frequency transient spikes may appear on the supply voltage
as well. This is due to the fast switching times on the PWM transis-
tors and the sharp edges of their gate voltages. Although these
V R S =
2
η V DD
(43)
transient spikes can reach several tens of millivolts at their peak,
where R L is the load resistance or resistance of the TEC and
is
they typically last for less than 20 ns and have a resonance greater
than 100 MHz. Additional bulk capacitance will not appreciably
the efficiency of the system. An estimate of efficiency can be calculated
either from the Calculating Power Dissipation and Efficiency section
affect the level of these spikes as such capacitance is not reactive at
or from Figures 16 and 17. A reasonable approximation is
=
these frequencies. Adding 0.01 μ F ceramic capacitors on the sup-
ply line near the PWM PMOS transistor can reduce this switching
noise. Inserting an RF inductor with a High-Q around 100 MHz in
series with PVDD will also block this noise from traveling back to
the power supply.
Setting Maximum Output Current and Short-Circuit
Protection
Although the maximum output voltage can be programmed
through VLIM to protect the TEC from overvoltage damage,
the user may wish to protect the ADN8830 circuit from a possible
short circuit at the output. Such a short could quickly damage the
external FETs or even the power supply since they would attempt
to drive excessive current. Figure 20 shows a simple modification
that will protect the system from an output short circuit.
0.85. Although the exact resistance of a TEC varies with tempera-
ture, an estimation can be made by dividing the maximum voltage
rating of the TEC by its maximum current rating.
In addition to providing protection against a short at the output,
this circuit will also protect the FETs against shoot-through current.
Shoot-through will not occur when using the recommended
transistors and additional capacitance shown in Tables V and VI.
However, if different transistors are used where their shoot-
through potential is unknown, implementing the short-circuit
protection circuit will unconditionally protect these transistors.
To set a maximum output current limit, use the circuit in Figure
21. This circuit can share the 10 m Ω power supply shunt resistor
as the short-circuit protection circuit to sense the output current.
In normal operation Q1 is on, pulling the ADN8830 VLIM pin
TO
V S
R S
PVDD
AVDD
down to the voltage set by VLIMIT. This sets the maximum out-
put voltage limit as described in the Setting the Maximum TEC
FETS
AND
DECOUPLING
PVDD
10m
Voltage and Current section.
CAPS
R3
Q1
R1
TO
V SY
R S
PVDD
AVDD
1k
R4
100k
V X
AD8601
R2
1k
FDV304P
OR EQUIVALENT
D1
MA116CT-ND
OR
EQUIVALENT
1M
C1
1 F
SD
FETS
AND
DECOUPLING PVDD
CAPS
R3
178
10m
R1
3.48k
AD8605
Q1
FDV301N
OR
EQUIVALENT
C1
1nF
TO
VLIM
R2
1.47k
R4
100k
V X
DENOTES
AGND
DENOTES
PGND
VLIMIT
Figure 20. Implementing Output Short-Circuit Protection
(0V TO 1.5V)
DENOTES
AGND
DENOTES
PGND
Figure 21. Setting a Maximum Output Current Limit
REV. D
–19 –
相关PDF资料 |
PDF描述 |
|---|---|
| ADP1046ACPZ-RL | IC DGTL CTRLR 32LFCSP |
| ADP1111ANZ-12 | IC REG BUCK BST INV 12V .2A 8DIP |
| ADP121-ACBZ12R7 | IC REG LDO 1.2V .15A 4WLCSP |
| ADP122AUJZ-2.9-R7 | IC REG LDO 2.9V .3A 5TSOT |
| ADP124ARHZ-2.85-R7 | IC REG LDO 2.85V .5A 8MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADN8830ACPZ-REEL7 | 功能描述:IC THERMO COOLER CTRLR 32-LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 标准包装:1 系列:- 应用:手持/移动设备 电流 - 电源:- 电源电压:3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-LLP-EP（4x4） 包装:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名称:LP3905SD-30DKR |
| ADN8830XCP-REEL | 制造商:Analog Devices 功能描述:- Tape and Reel |
| ADN8831 | 制造商:AD 制造商全称:Analog Devices 功能描述:Thermoelectric Cooler (TEC) Controller |
| ADN8831ACP | 制造商:Analog Devices 功能描述:- Bulk |
| ADN8831ACPZ-R2 | 制造商:Analog Devices 功能描述:Thermoelectric Cooler 32-Pin LFCSP EP T/R 制造商:Analog Devices 功能描述:THERMOELECTRIC COOLER 32LFCSP EP - Tape and Reel 制造商:Analog Devices 功能描述:HIGH PRECISION/EFFICIENCY TEC CONTROLLER 制造商:Analog Devices 功能描述:CONTROLLER TEC PROG C/V 32L |
发布紧急采购，3分钟左右您将得到回复。