- 您现在的位置：买卖IC网 > PDF目录1776 > ADN8830ACPZ-REEL (Analog Devices Inc)IC THERMO COOLER CNTRLR 32-LFCSP PDF资料下载
参数资料
| 型号： | ADN8830ACPZ-REEL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 8/22页 |
| 文件大小： | 0K |
| 描述： | IC THERMO COOLER CNTRLR 32-LFCSP |
| 标准包装： | 1 |
| 应用： | 热电冷却器 |
| 电流 - 电源： | 8mA |
| 电源电压： | 3.3 V ~ 5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 32-LFCSP-VQ（5x5） |
| 包装： | 剪切带 (CT) |
| 其它名称： | ADN8830ACPZ-REELCT |
ADN8830
response of the TEC’s temperature either in terms of settling time
or maximum current change. Details of how to adjust the compen-
sation network are given in the Compensation Loop section.
The ADN8830 can be easily integrated with a wavelength locker
for fine-tune temperature adjustment of the laser diode for a
specific wavelength. This is a useful topology for tunable wave-
length lasers. Details are highlighted in the Using the TEC
Controller ADN8830 with a Wave Locker section.
The TEC is driven differentially using an H-bridge configura-
tion to maximize the output voltage swing. The ADN8830
drives external transistors that are used to provide current to the
TEC. These transistors can be selected by the user based on the
simple integrator or PID loop, the dc forward gain of the
compensation section is equal to the open-loop gain of the
compensation amplifier, which is over 80 dB or 10,000. The
output from the compensation loop at COMPOUT is then fed
to the linear amplifier. The output of the linear amplifier at
OUT B is fed with COMPOUT into the PWM amplifier whose
output is OUT A. These two outputs provide the voltage drive
directly to the TEC. Including the external transistors, the gain of
the differential output section is fixed at 4. Details on the output
amplifiers can be found in the Output Driver Amplifiers section.
1.5V
maximum output current required for the TEC. The maximum
voltage across the TEC can be set through use of the VLIM pin
on the ADN8830.
To further improve the power efficiency of the system, one side
TEMPSET
THERMIN
4
2
INPUT
AMPLIFIER
1.5V
A V = 20
COMPENSATION PWM/LINEAR
AMPLIFIER AMPLIFIERS
19
9
OUT A
OUT B
of the H-bridge uses a switched output. Only one inductor and
A V = Z2/Z1
A V = 4
one capacitor are required to filter out the switching frequency.
The output voltage ripple is a function of the output inductor
12
TEMPCTL
Z1
13
Z2
14
COMPOUT
and capacitor and the switching frequency. For most applica-
tions, a 4.7 μ H inductor, 22 μ F capacitor, and switching frequency
of 1 MHz maintains less than ± 0.5% worst-case output voltage
ripple across the TEC. The other side of the H-bridge does not
require any additional circuitry.
The oscillator section of the ADN8830 controls the switched
output section. A single resistor sets the switching frequency
from 100 kHz to 1 MHz. The clock output is available at the
SYNCOUT pin and can be used to drive another ADN8830
device by connecting to its SYNCIN pin. The phase of the
clock is adjusted by a voltage applied to the PHASE pin, which
can be set by a simple resistor divider. Phase adjustment allows
two or more ADN8830 devices to operate from the same clock
frequency and not have all outputs switch simultaneously, which
could create an excessive power supply ripple. Details of how to
adjust the clock frequency and phase are given in the Setting the
Switching Frequency section.
For effective indication of a catastrophic system failure, the
ADN8830 alerts to open-circuit or short-circuit conditions from the
COMPFB
Figure 2. Signal Flow Block Diagram of the ADN8830
Thermistor Setup
The temperature of the thermal object, such as a laser diode, is
detected with a negative temperature coefficient (NTC) thermistor.
The thermistor’s resistance exhibits an exponential relationship to
the inverse of temperature, meaning the resistance decreases at
higher temperatures. Thus, by measuring the thermistor resistance,
temperature can be ascertained. Betatherm is a leading supplier
of NTC thermistors. Thermistor information and details can be
found at www.betatherm.com.
For this application, the resistance is measured using a voltage
divider. The thermistor is connected between THERMIN (Pin 2)
and AGND (Pin 30). Another resistor (R X ) is connected between
VREF (Pin 7) and THERMIN (Pin 2), creating a voltage divider
for the VREF voltage. Figure 3 shows the schematic for this
configuration.
V DD
thermistor, preventing an erroneous and potentially damaging
temperature correction from occurring. With some additional
external circuitry, output overcurrent detection can be imple-
mented to provide warning in the event of a TEC short-circuit
failure. This circuit is highlighted in the Setting Maximum
Output Current and Short-Circuit Protection section.
Signal Flow Diagram
Figure 2 shows the signal flow diagram through the ADN8830.
R X
R THERM
7
2
8
ADN8830
TEMPCTL = 20 × ( TEMPSET – THERMIN ) + 1 . 5
The input amplifier is fixed with a gain of 20. The voltage at
TEMPCTL can be expressed as
(1)
When the temperature is settled, the thermistor voltage will be
equal to the TEMPSET voltage, and the output of the input
amplifier will be 1.5 V.
The voltage at TEMPCTL is then fed into the compensation
amplifier whose frequency response is dictated by the compen-
sation network. Details on the compensation amplifier can be
found in the Compensation Loop section. When configured as a
–8 –
30
Figure 3. Connecting a Thermistor to the ADN8830
With the thermistor connected from THERMIN to AGND, the
voltage at THERMIN will decrease as temperature increases.
To maintain the proper input-to-output polarity in this configu-
ration, OUT A (Pin 19) should connect to the TEC– pin on the
TEC, and OUT B (Pin 9) should connect to the VTEC+ pin.
The thermistor can also be connected from VREF to THERMIN
with R X connecting to ground. In this case, OUT A must connect to
TEC+ with OUT B connected to TEC– for proper operation.
REV. D
相关PDF资料 |
PDF描述 |
|---|---|
| ADP1046ACPZ-RL | IC DGTL CTRLR 32LFCSP |
| ADP1111ANZ-12 | IC REG BUCK BST INV 12V .2A 8DIP |
| ADP121-ACBZ12R7 | IC REG LDO 1.2V .15A 4WLCSP |
| ADP122AUJZ-2.9-R7 | IC REG LDO 2.9V .3A 5TSOT |
| ADP124ARHZ-2.85-R7 | IC REG LDO 2.85V .5A 8MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADN8830ACPZ-REEL7 | 功能描述:IC THERMO COOLER CTRLR 32-LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 标准包装:1 系列:- 应用:手持/移动设备 电流 - 电源:- 电源电压:3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-LLP-EP（4x4） 包装:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名称:LP3905SD-30DKR |
| ADN8830XCP-REEL | 制造商:Analog Devices 功能描述:- Tape and Reel |
| ADN8831 | 制造商:AD 制造商全称:Analog Devices 功能描述:Thermoelectric Cooler (TEC) Controller |
| ADN8831ACP | 制造商:Analog Devices 功能描述:- Bulk |
| ADN8831ACPZ-R2 | 制造商:Analog Devices 功能描述:Thermoelectric Cooler 32-Pin LFCSP EP T/R 制造商:Analog Devices 功能描述:THERMOELECTRIC COOLER 32LFCSP EP - Tape and Reel 制造商:Analog Devices 功能描述:HIGH PRECISION/EFFICIENCY TEC CONTROLLER 制造商:Analog Devices 功能描述:CONTROLLER TEC PROG C/V 32L |
发布紧急采购，3分钟左右您将得到回复。