参数资料
型号: ADN8830ACPZ-REEL
厂商: Analog Devices Inc
文件页数: 20/22页
文件大小: 0K
描述: IC THERMO COOLER CNTRLR 32-LFCSP
标准包装: 1
应用: 热电冷却器
电流 - 电源: 8mA
电源电压: 3.3 V ~ 5 V
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 32-VFQFN 裸露焊盘,CSP
供应商设备封装: 32-LFCSP-VQ(5x5)
包装: 剪切带 (CT)
其它名称: ADN8830ACPZ-REELCT
ADN8830
5V
I OUTA
ADT70
I OUTB
+IN OA
TO THERM_IN
R3
82.5
+IN IA
OUT OA
= 1V @ 25 C
25mV/ C
R3
82.5
4.99k
RGA
RGB
INST
AMP
–IN IA
RTD
R3
1k
1k
GND
SENSE
AGND
OUT IA
–IN OA
1k
5.11k
NOTE: ADDITIONAL PINS OMITTED FOR CLARITY
Figure 22. Using an RTD for Temperature Feedback to the ADN8830
If the voltage at V SY drops below V X , Q1 is turned off and the
VLIM pin will be set to 1.5 V, effectively setting the maximum
voltage across the outputs to 0 V. The voltage divider for V X is
calculated from Equation 43.
TO
TEC
R S
10m
I L
TO
OUT B
AVDD
V HI
200k
AVDD
AVDD
AVDD
R1
3.48k
TO
VLIM
R2
Design Example 5
A maximum output current limit needs to be set at 1.5 A for a
TEC with a maximum voltage rating of 2.5 V. The ADN8830 is
powered from 5 V. The TEC resistance is estimated at 1.67 Ω and
8
AD626
1nF 300k
V X
AD8602
Q1,Q2
FDG6303N
OR
EQUIVA-
LENT
1.47k
efficiency at 85%. Using Equation 43, the voltage drop across
R S will be 8.8 mV when 1.5 A is delivered to the TEC. The trip
voltage V X is set to 4.991 V with R3 = 178 Ω and R4 = 100 k Ω
300k
as shown in Figure 21. To set the output voltage limit to 2.5 V,
the voltage at VLIMIT should be set to 0.875 V according to
TO
VREF
V LO 200k
VLIMIT
(0V TO 1.5V)
Equation 17.
The C1 capacitor is added to smooth the voltage transitions at
VLIM. Once an overcurrent condition is detected, the output
voltage will turn down to 0 V within 30 ms.
For a more exact measurement of the output current, place a
sense resistor in series with the output load, as shown in Figure 23.
The AD626 instrumentation amplifier is set for a gain of 100
with a reference voltage of 2.47 V from VREF. The output of
the AD626 is equal to 100 × R S × I L and is fed to the AD8602,
which is set up as a window comparator. With V X greater than
VLO but less than VHI, VLIM will be pulled down to the volt-
age at VLIMIT. Should V X fall outside the voltage window,
VLIM will be pulled to 1.5 V as in Figure 21. The trip points
should be set according to
Figure 23. High Accuracy Output Current Limit
The upper and lower trip point voltages can be set independently,
allowing different maximum output current limits depending on
the direction of the current. The resistor divider for VHI and
VLO is tapped to VREF to maintain window accuracy with any
changes in VREF. Using the values from Figure 23 with a 5 V
supply, the output current will not exceed 1.5 A in either direction.
Adding the current sensing resistor will slightly reduce efficiency.
The power dissipated by this resistor is D × ITEC2 × R S if the
TEC is heating, or (1–D) × ITEC2 × R S if the TEC is cooling.
Include this when calculating efficiency as described in the
Calculating Power Dissipation and Efficiency section.
VHI = VREF + 100 × R S I LIMIT +
VLO = VREF – 100 × R S I LIMIT –
(44)
–20 –
REV. D
相关PDF资料
PDF描述
ADP1046ACPZ-RL IC DGTL CTRLR 32LFCSP
ADP1111ANZ-12 IC REG BUCK BST INV 12V .2A 8DIP
ADP121-ACBZ12R7 IC REG LDO 1.2V .15A 4WLCSP
ADP122AUJZ-2.9-R7 IC REG LDO 2.9V .3A 5TSOT
ADP124ARHZ-2.85-R7 IC REG LDO 2.85V .5A 8MSOP
相关代理商/技术参数
参数描述
ADN8830ACPZ-REEL7 功能描述:IC THERMO COOLER CTRLR 32-LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 标准包装:1 系列:- 应用:手持/移动设备 电流 - 电源:- 电源电压:3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-LLP-EP(4x4) 包装:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名称:LP3905SD-30DKR
ADN8830XCP-REEL 制造商:Analog Devices 功能描述:- Tape and Reel
ADN8831 制造商:AD 制造商全称:Analog Devices 功能描述:Thermoelectric Cooler (TEC) Controller
ADN8831ACP 制造商:Analog Devices 功能描述:- Bulk
ADN8831ACPZ-R2 制造商:Analog Devices 功能描述:Thermoelectric Cooler 32-Pin LFCSP EP T/R 制造商:Analog Devices 功能描述:THERMOELECTRIC COOLER 32LFCSP EP - Tape and Reel 制造商:Analog Devices 功能描述:HIGH PRECISION/EFFICIENCY TEC CONTROLLER 制造商:Analog Devices 功能描述:CONTROLLER TEC PROG C/V 32L