- 您现在的位置：买卖IC网 > PDF目录16743 > ADP1043AACPZ-R7 (Analog Devices Inc)IC THERMO COOLER CTLR 32LFCSP PDF资料下载
参数资料
| 型号： | ADP1043AACPZ-R7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 13/72页 |
| 文件大小： | 0K |
| 描述： | IC THERMO COOLER CTLR 32LFCSP |
| 标准包装： | 1,500 |
| 应用： | 电源 |
| 输入电压： | 0 V ~ 1.55 V |
| 电源电压： | 3.1 V ~ 3.6 V |
| 电流 - 电源： | 20mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 32-LFCSP-VQ（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页
ADP1043A
VOLTAGE SENSE AND CONTROL LOOP
Multiple voltage sense inputs on the ADP1043A are used for the
monitoring, control, and protection of the power supply output.
The voltage information is available through the I 2 C interface.
All voltage sense points can be calibrated digitally to remove
any errors due to external components. This calibration can be
performed in the production environment, and the settings can
be stored in the EEPROM of the ADP1043A (see the Power
The update rate of the ADC from a control loop standpoint
is set to the switching frequency. Therefore, if the switching
frequency is set to 100 kHz, the ADC outputs a signal every
100 kHz to the control loop. Because the Σ-Δ modulators of the
ADC sample at 1.6 MHz, the output of the ADC is the average
of the 16 readings taken during the 1.6 MHz time frame.
For voltage monitoring, the VS1, VS2, and VS3 voltage value
registers are updated every 10 ms. The ADP1043A stores every
ADC sample for 10 ms and then outputs the average value at the
end of the 10 ms period. Therefore, if these registers are read at
least every 10 ms, a true average value is read. The same applies
to the CS1 and CS2 current readings.
For the control loop, the high speed signal always comes from
the VS1 high speed ADC. The low speed signal normally comes
from the VS3 low speed ADC. However, during soft start or in
response to a load OVP or other fault condition, the ADP1043A
can switch its low speed regulating point from VS3 to VS1.
VS1 Operation (VS1)
VS1 is used for the monitoring and protection of the power
supply voltage at the output of the LC stage, upstream of the
OrFET. This is also the high frequency feedback loop for the
power supply. The VS1 sense point on the power rail needs an
external resistor divider to bring the nominal common-mode
signal to 1 V at the VS1 pin (see Figure 13). The resistor divider
is necessary because the ADP1043A VS1 ADC input range is
0 V to 1.55 V. This divided-down signal is internally fed into a
high speed and a low speed Σ-Δ ADC. The output of the VS1
ADCs goes to the digital filter.
The high speed ADC has a 2 MHz bandwidth and is run from
a 25 MHz clock. It has a range of ±18 mV. When the sampling
rate is 200 kHz, there is 0.6 mV (two LSBs) of quantization noise.
Increasing the sampling rate to 400 kHz increases the quanti-
zation noise to 1.2 mV.
In the event of a load overvoltage condition, the power supply
is regulated from the VS1 sense point, rather than from the
VS3 sense point.
VS2 Operation (VS2)
VS2 is typically used for the monitoring and protection of the
output of the power supply, downstream of the OrFET. It is
used with VS1 to control the OrFET gate drive turn-on. The
VS2 sense point on the power rail needs an external resistor
divider to bring the nominal common-mode signal to 1 V at
the VS2 pin (see Figure 13). The resistor divider is necessary
12V
12V
12V
because the ADP1043A VS2 ADC input range is 0 V to 1.55 V.
This divided-down signal is internally fed into an ADC. The
LOAD
output of the VS2 ADC goes to the VS2 voltage value register
(Register 0x16).
1V
11k ?
1k ?
1V
11k ?
1k ?
VS3 Operation (VS3+, VS3?)
VS3± is used for the monitoring and protection of the remote
load voltage. It is a fully differential input. This is the main
PGND
VS1
VS2
VS3+
VS3–
11k ?
1V
1k ?
feedback sense point for the power supply control loop. The
VS3 sense point on the power rail needs an external resistor
divider to bring the nominal common-mode signal to 1 V at
the VS3± pins (see Figure 13). The resistor divider is necessary
VS1
HIGH ADC
SPEED
6 BITS
VS1
LOW ADC
SPEED
12 BITS
VS2 ADC
12 BITS
VS3 ADC
12 BITS
because the ADP1043A VS3 ADC input range is 0 V to 1.55 V.
This divided-down signal is internally fed into an ADC. The
output of the VS3 ADC goes to the digital filter.
HIGH
FREQUENCY
ADCs
FEEDBACK
LOOP
DIGITAL
FILTER
LOW FREQUENCY
FEEDBACK LOOP
The ADP1043A includes several ADCs. The high speed ADC is
described in the VS1 Operation (VS1) section. The other ADCs
are low speed, high resolution. They have a 1 kHz bandwidth
and 12-bit resolution. Each ADC has its own voltage reference
Figure 13. Voltage Sense Configuration
for added protection from potential failure. The digital output
of each ADC is readable through the appropriate value register.
Rev. 0 | Page 13 of 72
相关PDF资料 |
PDF描述 |
|---|---|
| RBC13DRTH-S93 | CONN EDGECARD 26POS .100 EXTEND |
| H6PPH-2406M | DIP CABLE - HDP24H/AE24M/HDP24H |
| GBC18DRTS-S93 | CONN EDGECARD 36POS DIP .100 SLD |
| 6.3TZV220M6.3X6.1 | CAP ALUM 220UF 6.3V 20% SMD |
| H0PPS-2418G | DIP CABLE - HDP24S/AE24G/HDP24S |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADP1043AACPZ-RL | 功能描述:IC SECONDARY SIDE CTRLR 32LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ADP1043ACPZ | 制造商:Analog Devices 功能描述:DC DC CNTRLR QUINT-OUT W/PWM 3.3V 32LFCSP EP - Trays |
| ADP1043ACPZ-RL | 制造商:Analog Devices 功能描述:DC DC CNTRLR QUINT-OUT W/PWM 3.3V 32LFCSP EP - Tape and Reel |
| ADP1043ADC1-EVALZ | 功能描述:BOARD EVAL ADP1043A DAUGHTERCARD RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081 |
| ADP1043AFB100EVALZ | 功能描述:BOARD EVALUATION ADP1043A 100W RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081 |
发布紧急采购，3分钟左右您将得到回复。