参数资料
| 型号： | ADP1048-600-EVALZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 38/84页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL ADP1048-600 |
| 标准包装： | 1 |
| 主要目的： | 电源管理，功率因数校正 |
| 已用 IC / 零件： | ADP1048 |
| 主要属性： | 600W，385V 输出，85~265VAC 输入 |
| 已供物品： | 板 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页当前第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页
ADP1047/ADP1048
EEPROM
The ADP1047 / ADP1048 have a built-in EEPROM controller
that is used to communicate with the embedded 8K × 8-byte
EEPROM. The EEPROM, also called Flash?/EE, is partitioned
into two major blocks: the INFO block and the main block.
The INFO block contains 128 8-bit bytes, and the main block
contains 8K 8-bit bytes. The main block is further partitioned
into 16 pages, each page containing 512 bytes.
OVERVIEW
The EEPROM controller provides an interface between the
user can control data access to and from the EEPROM through
this controller interface. Separate PMBus commands are avail-
able for the read, write, and erase operations to the EEPROM.
Communication is initiated by the master device sending a
command to the PMBus slave device to access data from or
send data to the EEPROM. Read, write, and erase commands
are supported. Data is transferred between devices in a byte
wide format. Using a read command, data is received from the
EEPROM and transmitted to the master device. Using a write
command, data is received from the master device and stored
in the EEPROM through the EEPROM controller.
PAGE ERASE OPERATION
The main block consists of 16 equivalent pages of 512 bytes
each, numbered Page 0 to Page 15. Page 0 and Page 1 of the
main block are reserved for storing the default settings and user
settings, respectively. The user cannot perform a page erase
operation to Page 0 or Page 1.
Main Block Page Erase (Page 2 to Page 15)
To erase any page from Page 2 to Page 15 of the main block, the
Data Sheet
The EEPROM allows erasing of whole pages only; therefore, to
change the data of any single byte in a page, the entire page
must first be erased (set high) for that byte to be writable.
Subsequent writes to any bytes in that page are allowed as long
as that byte has not been written to a low previously.
READ OPERATION (BYTE READ AND BLOCK READ)
Read from Page 0 and Page 1
Page 0 and Page 1 of the main block are reserved for storing the
default settings and user settings, respectively, and are meant to
prevent third-party access to this data. To read from Page 0 or
Page 1, the user must first unlock the EEPROM (see the Unlock
EEPROM section). After they are unlocked, Page 0 and Page 1
are readable using the EEPROM_DATA_xx commands, as
described in the Read from Page 2 to Page 15 section. Note that
when the EEPROM is locked, a read from Page 0 and Page 1
returns invalid data.
Read from Page 2 to Page 15
Data in Page 2 to Page 15 is always readable, even with the
EEPROM locked. The data in the EEPROM main block can
be read one byte at a time or in multiple bytes in series using
the EEPROM_DATA_xx commands (Command Code 0xB0
to Command Code 0xBF).
Before executing this command, the user must program the
number of bytes to read using the EEPROM_NUM_RD_BYTES
command (Register 0xD2). Also, the user can program the offset
from the page boundary where the first read byte is returned
using the EEPROM_ADDR_OFFSET command (Register 0xD3).
In the following example, three bytes from Page 4 are read from
EEPROM, starting from the fifth byte of that page.
EEPROM must first be unlocked for access. For instructions on
1.
Set number of return bytes = 3.
how to unlock the EEPROM, see the Unlock EEPROM section.
Page 2 to Page 15 of the main block can be individually erased
S
SLAVE
ADDRESS
W
A
0xD2
A
0x03
A
P
using the EEPROM_PAGE_ERASE command (Register 0xD4).
For example, to perform a page erase of Page 10, execute the
MASTER TO SLAVE
SLAVE TO MASTER
following command:
2.
Set address offset = 5.
S
SLAVE
ADDRESS
W
A
COMMAND
CODE
A
DATA BYTE
A
P
S
SLAVE
ADDRESS
W
A
0xD3
A
0x00
A
0x05
A
P
MASTER TO SLAVE
SLAVE TO MASTER
MASTER TO SLAVE
SLAVE TO MASTER
Figure 43. Example Erase Command
3.
Read three bytes from Page 4.
In this example, Command Code = 0xD4 and Data Byte =
0x0A.
S
SLAVE
ADDRESS
W
A
0xB4
A
Sr
SLAVE
ADDRESS
R
A
Note that it is important to wait at least 35 ms for the page
erase operation to complete before executing the next PMBus
command.
BYTE COUNT =
0x03
MASTER TO SLAVE
SLAVE TO MASTER
A
DATA BYTE
1
A
...
DATA BYTE
3
A
P
Note that the block read command can read a maximum of 256
bytes for any single transaction.
Rev. 0 | Page 38 of 84
相关PDF资料 |
PDF描述 |
|---|---|
| ADP190CB-EVALZ | BOARD EVAL ADP190 |
| ADP191CB-EVALZ | EVAL BOARD FOR ADP191 |
| ADP194CB-EVALZ | BOARD EVAL FOR ADP194ACBZ |
| ADP195CP-EVALZ | BOARD EVAL FOR ADP195ACPZ |
| ADP197CB-EVALZ | BOARD EVAL FOR ADP197ACBZ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADP1048ARQZ-R7 | 功能描述:IC DGTL PFC CTRLR 24QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - PFC（功率因数修正） 系列:- 产品培训模块:GreenChip Synchronous Rectification Control Family of ICs 标准包装:1 系列:- 模式:间歇导电（DCM） 频率 - 开关:- 电流 - 启动:- 电源电压:8.6 V ~ 38 V 工作温度:-20°C ~ 150°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SO 包装:Digi-Reel® 其它名称:568-5348-6 |
| ADP1048DC1-EVALZ | 功能描述:DAUGHTERCARD ADP1048 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081 |
| ADP1048WARQZ-R7 | 功能描述:PFC IC Average Current 30kHz ~ 400kHz 24-QSOP 制造商:analog devices inc. 系列:- 包装:带卷（TR） 零件状态:有效 模式:平均电流 频率 - 开关:30kHz ~ 400kHz 电流 - 启动:- 电压 - 电源:3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:24-SSOP（0.209"，5.30mm 宽） 供应商器件封装:24-QSOP 标准包装:1,000 |
| ADP1050ACPZ-R7 | 功能描述:Power Supply Controller Power Supply Controller/Monitor 20-LFCSP-WQ (4x4) 制造商:analog devices inc. 系列:- 包装:剪切带（CT） 零件状态:有效 应用:电源控制器/监控器 电压 - 输入:0 V ~ 1.6 V 电压 - 电源:3 V ~ 3.6 V 电流 - 电源:28.5mA 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:20-WFQFN 裸露焊盘，CSP 供应商器件封装:20-LFCSP-WQ（4x4） 标准包装:1 |
| ADP1050ACPZ-RL | 功能描述:Power Supply Controller Power Supply Controller/Monitor 20-LFCSP-WQ (4x4) 制造商:analog devices inc. 系列:- 包装:带卷（TR） 零件状态:在售 应用:电源控制器/监控器 电压 - 输入:0 V ~ 1.6 V 电压 - 电源:3 V ~ 3.6 V 电流 - 电源:28.5mA 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:20-WFQFN 裸露焊盘，CSP 供应商器件封装:20-LFCSP-WQ（4x4） 标准包装:5,000 |
发布紧急采购，3分钟左右您将得到回复。