参数资料
| 型号： | ADUC7122BBCZ-RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 76/96页 |
| 文件大小： | 0K |
| 描述： | PRECISION ANALOG MCU I.C |
| 标准包装： | 1 |
| 系列： | MicroConverter® ADuC7xxx |
| 核心处理器： | ARM7 |
| 芯体尺寸： | 16/32-位 |
| 速度： | 41.78MHz |
| 连通性： | I²C，SPI，UART/USART |
| 外围设备： | POR，PWM，WDT |
| 输入/输出数： | 32 |
| 程序存储器容量： | 126KB（63K x 16） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 8K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 3 V ~ 3.6 V |
| 数据转换器： | A/D 13x12b，D/A 12x12b |
| 振荡器型： | 内部 |
| 工作温度： | -10°C ~ 95°C |
| 封装/外壳： | 108-LFBGA，CSPBGA |
| 包装： | 标准包装 |
| 其它名称： | ADUC7122BBCZ-RLDKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页当前第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页
ADuC7122
Rev. 0 | Page 78 of 96
FIQEN
FIQEN provides the value of the current enable mask. When a
bit is set to 1, the corresponding source request is enabled
to create an FIQ exception. When a bit is set to 0, the corre-
sponding source request is disabled or masked, which does not
create an FIQ exception. The FIQEN register cannot be used to
disable an interrupt.
FIQEN Register
Name:
FIQEN
Address:
0xFFFF0108
Default Value:
0x00000000
Access:
Read/write
FIQCLR
FIQCLR is a write-only register that allows the FIQEN register
to clear to mask an interrupt source. Each bit that is set to 1
clears the corresponding bit in the FIQEN register without
affecting the remaining bits. The pair of registers, FIQEN and
FIQCLR, allows independent manipulation of the enable mask
without requiring an atomic read-modify-write.
FIQCLR Register
Name:
FIQCLR
Address:
0xFFFF010C
Default Value:
0x00000000
Access:
Write only
FIQSTA
FIQSTA is a read-only register that provides the current enabled
FIQ source status (effectively a logic AND of the FIQSIG and
FIQEN bits). When set to 1, that source generates an active FIQ
request to the ARM7TDMI core. There is no priority encoder
or interrupt vector generation. This function is implemented in
software in a common interrupt handler routine.
FIQSTA Register
Name:
FIQSTA
Address:
0xFFFF0100
Default Value:
0x00000000
Access:
Read only
Programmed Interrupts
Because the programmed interrupts are not maskable, they are
controlled by another register (SWICFG) that writes into both
IRQSTA and IRQSIG registers and/or the FIQSTA and FIQSIG
registers at the same time.
The 32-bit register dedicated to software interrupt is SWICFG,
described in Table 129. This MMR allows the control of a
programmed source interrupt.
Table 129. SWICFG MMR Bit Designations
Bit
Description
31 to 3
Reserved.
2
Programmed Interrupt FIQ. Setting/clearing this bit
corresponds to setting/clearing Bit 1 of FIQSTA and
FIQSIG.
1
Programmed Interrupt IRQ. Setting/clearing this bit
corresponds to setting/clearing Bit 1 of IRQSTA and
IRQSIG.
0
Reserved.
Any interrupt signal must be active for at least the minimum
interrupt latency time to be detected by the interrupt controller
and by the user in the IRQSTA/FIQSTA register.
08
75
5-
0
37
POINTER TO
FUNCTION
(IRQVEC)
IRQ_SOURCE
FIQ_SOURCE
PROGRAMMABLE PRIORITY
PER INTERRUPT (IRQP0/IRQP1/IRQP2)
INTERNAL
ARBITER
LOGIC
INTERRUPT VECTOR
BIT 31 TO
BIT 23
UNUSED
BIT 1 TO
BIT 0
LSB
BIT 22 TO BIT 7
(IRQBASE)
BIT 6 TO
BIT 2
HIGHEST
PRIORITY
ACTIVE IRQ
Figure 36. Interrupt Structure
Vectored Interrupt Controller (VIC)
The ADuC7122 incorporates an enhanced interrupt control
system or vectored interrupt controller. The vectored interrupt
controller for IRQ interrupt sources is enabled by setting Bit 0
of the IRQCONN register. Similarly, Bit 1 of IRQCONN enables
the vectored interrupt controller for the FIQ interrupt sources.
The vectored interrupt controller provides the following
enhancements to the standard IRQ/FIQ interrupts:
Vectored interrupts—allow a user to define separate
interrupt service routine addresses for every interrupt
source. This is achieved by using the IRQBASE and
IRQVEC registers.
IRQ/FIQ interrupts—can be nested up to eight levels
depending on the priority settings. An FIQ still has a
higher priority than an IRQ. Therefore, if the VIC is enabled
for both the FIQ and IRQ and prioritization is maximized,
then it is possible to have 16 separate interrupt levels.
Programmable interrupt priorities—using the IRQP0 to
IRQP2 registers, an interrupt source can be assigned an
interrupt priority level value between 1 and 8.
相关PDF资料 |
PDF描述 |
|---|---|
| ADUC7126BSTZ126-RL | IC MCU 16/32B 126KB FLASH 80LQFP |
| ADUC7129BSTZ126 | IC DAS MCU ARM7 ADC/DDS 80-LQFP |
| ADUC812BSZ-REEL | IC MCU FLASH 12BIT ADC 52MQFP |
| ADUC814BRU | IC ADC 12BIT W/FLASH MCU 28TSSOP |
| ADUC816BCP | IC MCU 8K FLASH ADC/DAC 56LFCSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADUC7124 | 制造商:AD 制造商全称:Analog Devices 功能描述:Precision Analog Microcontroller, 12-Bit Analog I/O, Large Memory, ARM7TDMI MCU with Enhanced IRQ Handler |
| ADUC7124BCPZ126 | 功能描述:IC DAS MCU ARM7 ADC/DDS 64LQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 标准包装:250 系列:LPC11Uxx 核心处理器:ARM? Cortex?-M0 芯体尺寸:32-位 速度:50MHz 连通性:I²C，Microwire，SPI，SSI，SSP，UART/USART，USB 外围设备:欠压检测/复位，POR，WDT 输入/输出数:40 程序存储器容量:96KB（96K x 8） 程序存储器类型:闪存 EEPROM 大小:4K x 8 RAM 容量:10K x 8 电压 - 电源 (Vcc/Vdd):1.8 V ~ 3.6 V 数据转换器:A/D 8x10b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:48-LQFP 包装:托盘 其它名称:568-9587 |
| ADUC7124BCPZ126-RL | 功能描述:IC DAS MCU ARM7 ADC/DDS 64-LQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 标准包装:38 系列:Encore!® XP® 核心处理器:eZ8 芯体尺寸:8-位 速度:5MHz 连通性:IrDA，UART/USART 外围设备:欠压检测/复位，LED，POR，PWM，WDT 输入/输出数:16 程序存储器容量:4KB（4K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:1K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 3.6 V 数据转换器:- 振荡器型:内部 工作温度:-40°C ~ 105°C 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 包装:管件 其它名称:269-4116Z8F0413SH005EG-ND |
| ADUC7126BSTZ126 | 功能描述:IC MCU 16/32B 126KB FLASH 80LQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 标准包装:250 系列:LPC11Uxx 核心处理器:ARM? Cortex?-M0 芯体尺寸:32-位 速度:50MHz 连通性:I²C，Microwire，SPI，SSI，SSP，UART/USART，USB 外围设备:欠压检测/复位，POR，WDT 输入/输出数:40 程序存储器容量:96KB（96K x 8） 程序存储器类型:闪存 EEPROM 大小:4K x 8 RAM 容量:10K x 8 电压 - 电源 (Vcc/Vdd):1.8 V ~ 3.6 V 数据转换器:A/D 8x10b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:48-LQFP 包装:托盘 其它名称:568-9587 |
| ADUC7126BSTZ126I | 功能描述:IC MCU 16/32B 126KB FLASH 80LQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 标准包装:250 系列:LPC11Uxx 核心处理器:ARM? Cortex?-M0 芯体尺寸:32-位 速度:50MHz 连通性:I²C，Microwire，SPI，SSI，SSP，UART/USART，USB 外围设备:欠压检测/复位，POR，WDT 输入/输出数:40 程序存储器容量:96KB（96K x 8） 程序存储器类型:闪存 EEPROM 大小:4K x 8 RAM 容量:10K x 8 电压 - 电源 (Vcc/Vdd):1.8 V ~ 3.6 V 数据转换器:A/D 8x10b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:48-LQFP 包装:托盘 其它名称:568-9587 |
发布紧急采购，3分钟左右您将得到回复。