参数资料
| 型号： | ADUC836BCPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 24/80页 |
| 文件大小： | 0K |
| 描述： | IC MCU 62K FLASH ADC/DAC 56LFCSP |
| 标准包装： | 1 |
| 系列： | MicroConverter® ADuC8xx |
| 核心处理器： | 8052 |
| 芯体尺寸： | 8-位 |
| 速度： | 12.58MHz |
| 连通性： | EBI/EMI，I²C，SPI，UART/USART |
| 外围设备： | POR，PSM，PWM，温度传感器，WDT |
| 输入/输出数： | 34 |
| 程序存储器容量： | 62KB（62K x 8） |
| 程序存储器类型： | 闪存 |
| EEPROM 大小： | 4K x 8 |
| RAM 容量： | 2.25K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2.7 V ~ 5.25 V |
| 数据转换器： | A/D 7x16b; D/A 1x12b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 56-VFQFN 裸露焊盘，CSP |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页
ADuC836
–30–
ADuC836
–31–
Flash/EE Program Memory
The ADuC836 contains a 64 Kbyte array of Flash/EE program
memory.The lower 62 Kbytes of this program memory are avail-
able to the user, and can be used for program storage or indeed
as additional NV data memory.
The upper 2 Kbytes of this Flash/EE program memory array con-
tain permanently embedded firmware, allowing in-circuit serial
download, serial debug, and nonintrusive single pin emulation.
These 2 Kbytes of embedded firmware also contain a power-on
configuration routine that downloads factory calibrated coeffi-
cients to the various calibrated peripherals (ADC, temperature
sensor, current sources, band gap references, and so on).
This 2 Kbyte embedded firmware is hidden from user code.
Attempts to read this space will read 0s, i.e., the embedded firm-
ware appears as NOP instructions to user code.
In normal operating mode (power-up default), the 62 Kbytes of
user Flash/EE program memory appear as a single block.This
block is used to store the user code, as shown in Figure 17.
FFFFH
0000H
F800H
F7FFH
USER PROGRAM MEMORY
62 KBYTES OF FLASH/EE PROGRAM MEMORY IS
AVAILABLE TO THE USER. ALL OF THIS SPACE CAN
BE PROGRAMMED FROM THE PERMANENTLY
EMBEDDED DOWNLOAD/DEBUG KERNEL OR IN
PARALLEL PROGRAMMING MODE.
EMBEDDED DOWNLOAD/DEBUG KERNEL
PERMANENTLY EMBEDDED FIRMWARE ALLOWS CODE
TO BE DOWNLOADED TO ANY OF THE 62 KBYTES OF
ON-CHIP PROGRAM MEMORY. THE KERNEL PROGRAM
APPEARS AS ‘NOP’ INSTRUCTIONS TO USER CODE.
62 KBYTE
2 KBYTE
Figure 17. Flash/EE Program Memory Map in Normal Mode
In Normal mode, the 62 Kbytes of Flash/EE program memory
can be programmed by serial downloading or parallel processing:
(1) Serial Downloading (In-Circuit Programming)
The ADuC836 facilitates code download via the standard UART
serial port.The ADuC836 will enter Serial Download mode after
a reset or power cycle if the PSEN pin is pulled low through an
external 1 k resistor. Once in serial download mode, the hidden
embedded download kernel will execute.This allows the user to
download code to the full 62 Kbytes of Flash/EE program memo-
ry while the device is in circuit in its target application hardware.
A PC serial download executable is provided as part of the
ADuC836 QuickStart development system. Application Note
uC004 fully describes the serial download protocol that is used
by the embedded download kernel.This Application Note is
available at www.analog.com/microconverter.
(2) Parallel Programming
The Parallel Programming mode is fully compatible with con-
ventional third party Flash or EEPROM device programmers.
A block diagram of the external pin configuration required to
support parallel programming is shown in Figure 18. In this mode,
Ports 0 and 2 operate as the external address bus interface, P3
operates as the external data bus interface, and P1.0 operates as
the Write Enable strobe. Port 1.1, P1.2, P1.3, and P1.4 are used
as a general configuration port that configures the device for vari-
ous program and erase operations during parallel programming.
Table XIII. Flash/EE Memory Parallel Programming Modes
Port 1 Pins
P1.4
P1.3
P1.2
P1.1
Programming Mode
0
Erase Flash/EE Program,
Data, and Security Modes
1
0
1
Read Device Signature/ID
1
0
1
0
Program Code Byte
0
1
0
Program Data Byte
1
0
1
Read Code Byte
0
1
Read Data Byte
1
0
Program Security Modes
1
0
1
Read/Verify Security Modes
All other codes
Redundant
VDD
GND
P1.1 -> P1.4
PSEN
RESET
P3
P0
P2
ADuC836
5V
PROGRAM MODE
(SEE TABLE XIII)
GND
PROGRAM
DATA
(D0–D7)
PROGRAM
ADDRESS
(A0–A13)
(P2.0 = A0)
(P1.7 = A13)
COMMAND
ENABLE
P1.0
EA
ENTRY
SEQUENCE
VDD
GND
P1.5 -> P1.7
TIMING
Figure 18. Flash/EE Memory Parallel Programming
REV. A
相关PDF资料 |
PDF描述 |
|---|---|
| ADUC843BSZ62-5 | IC ADC 12BIT W/FLASH MCU 52-MQFP |
| ADUC845BCPZ62-5 | IC FLASH MCU W/24BIT ADC 56-CSP |
| ADUC847BCPZ62-5 | IC MCU FLASH W/24BIT ADC 56-CSP |
| ADV202BBCZ-135 | IC CODEC VIDEO 135MHZ 144CSPBGA |
| ADV212BBCZ-115 | IC CODEC VID JPEG 2000 121CSPBGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADUC836BCPZ-REEL | 功能描述:IC MCU 62K FLASH ADC/DAC 56LFCSP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 标准包装:38 系列:Encore!® XP® 核心处理器:eZ8 芯体尺寸:8-位 速度:5MHz 连通性:IrDA，UART/USART 外围设备:欠压检测/复位，LED，POR，PWM，WDT 输入/输出数:16 程序存储器容量:4KB（4K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:1K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 3.6 V 数据转换器:- 振荡器型:内部 工作温度:-40°C ~ 105°C 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 包装:管件 其它名称:269-4116Z8F0413SH005EG-ND |
| ADUC836BS | 制造商:Analog Devices 功能描述:MCU 8-bit ADuC8xx 8052 CISC 62KB Flash 3.3V/5V 52-Pin MQFP 制造商:Analog Devices 功能描述:8BIT MCU +16BIT DUAL ADC MQFP52 |
| ADUC836BS | 制造商:Analog Devices 功能描述:IC SEMICONDUCTOR ((NS)) |
| ADUC836BSZ | 功能描述:IC ADC DUAL 16BIT W/MCU 52-MQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 标准包装:250 系列:56F8xxx 核心处理器:56800E 芯体尺寸:16-位 速度:60MHz 连通性:CAN，SCI，SPI 外围设备:POR，PWM，温度传感器，WDT 输入/输出数:21 程序存储器容量:40KB（20K x 16） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:6K x 16 电压 - 电源 (Vcc/Vdd):2.25 V ~ 3.6 V 数据转换器:A/D 6x12b 振荡器型:内部 工作温度:-40°C ~ 125°C 封装/外壳:48-LQFP 包装:托盘 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323 |
| ADUC841 | 制造商:AD 制造商全称:Analog Devices 功能描述:MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU |
发布紧急采购，3分钟左右您将得到回复。