参数资料
| 型号： | ADUC836BCPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 62/80页 |
| 文件大小： | 0K |
| 描述： | IC MCU 62K FLASH ADC/DAC 56LFCSP |
| 标准包装： | 1 |
| 系列： | MicroConverter® ADuC8xx |
| 核心处理器： | 8052 |
| 芯体尺寸： | 8-位 |
| 速度： | 12.58MHz |
| 连通性： | EBI/EMI，I²C，SPI，UART/USART |
| 外围设备： | POR，PSM，PWM，温度传感器，WDT |
| 输入/输出数： | 34 |
| 程序存储器容量： | 62KB（62K x 8） |
| 程序存储器类型： | 闪存 |
| EEPROM 大小： | 4K x 8 |
| RAM 容量： | 2.25K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2.7 V ~ 5.25 V |
| 数据转换器： | A/D 7x16b; D/A 1x12b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 56-VFQFN 裸露焊盘，CSP |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页当前第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页
ADuC836
–64–
ADuC836
–65–
Power Saving Modes
Setting the Idle and Power-Down Mode Bits, PCON.0 and
PCON.1, respectively, in the PCON SFR described in Table II
allows the chip to be switched from Normal mode into Idle
mode, and also into full Power-Down mode.
In Idle mode, the oscillator continues to run, but the core clock
generated from the PLL is halted.The on-chip peripherals
continue to receive the clock and remain functional.The CPU
status is preserved with the stack pointer, program counter, and
all other internal registers maintain their data during Idle mode.
Port pins and DAC output pins also retain their states, and ALE
and PSEN outputs go high in this mode.The chip will recover
from Idle mode upon receiving any enabled interrupt, or upon
receiving a hardware reset.
In Power-Down mode, both the PLL and the clock to the core are
stopped.The on-chip oscillator can be halted or can continue to
oscillate, depending on the state of the oscillator power-down bit
(OSC_PD) in the PLLCON SFR.The TIC, being driven directly
from the oscillator, can also be enabled during power-down. All
other on-chip peripherals, however, are shut down. Port pins retain
their logic levels in this mode, but the DAC output goes to a high
impedance state (three-state) while ALE and PSEN outputs are
held low. During full Power-Down mode with the oscillator and
wake-up timer running, the ADuC836 typically consumes a total
of 15 A.There are five ways of terminating Power-Down mode:
Asserting the RESET Pin (Pin 15)
Returns to Normal mode. All registers are set to their reset default
value and program execution starts at the reset vector once the
RESET pin is deasserted.
Cycling Power
All registers are set to their default state and program execution
starts at the reset vector approximately 128 ms later.
Time Interval Counter (TIC) Interrupt
If the OSC_PD bit in the PLLCON SFR is clear, the 32 kHz
oscillator will remain powered up even in Power-Down mode.
If the Time Interval Counter (Wakeup/RTC timer) is enabled,
a TIC interrupt will wake the ADuC836 up from Power-Down
mode.The CPU services the TIC interrupt.The RETI at the end
of the TIC ISR will return the core to the instruction after the
one that enabled power-down.
SPI Interrupt
If the SERIPD bit in the PCON SFR is set, then an SPI interrupt,
if enabled, will wake up the ADuC836 from Power-Down mode.
The CPU services the SPI interrupt.The RETI at the end of the
ISR will return the core to the instruction after the one that enabled
power-down.
INT0 Interrupt
If the INT0PD bit in the PCON SFR is set, an external interrupt 0,
if enabled, will wake up the ADuC836 from power-down.The
CPU services the SPI interrupt.The RETI at the end of the ISR
will return the core to the instruction after the one that enabled
power-down.
Wake-Up from Power-Down Latency
Even with the 32 kHz crystal enabled during power-down, the PLL
will take some time to lock after a wake-up from power-down.Typ-
ically, the PLL will take about 1 ms to lock. During this time, code
will execute, but not at the specified frequency. Some operations
require an accurate clock, for example, UART communications,
to achieve specified 50 Hz/60 Hz rejection from the ADCs.The
following code may be used to wait for the PLL to lock:
WAITFORLOCK:
MOV A, PLLCON
JNB ACC.6, WAITFORLOCK
If the crystal has been powered down during power-down, there
is an additional delay associated with the startup of the crystal
oscillator before the PLL can lock. 32 kHz crystals are inherently
slow to oscillate, typically taking about 150 ms. Once again, during
this time before lock, code will execute, but the exact frequency
of the clock cannot be guaranteed. Again for any timing sensitive
operations, it is recommended to wait for lock using the lock bit
in PLLCON, as shown in the code above.
Grounding and Board Layout Recommendations
As with all high resolution data converters, special attention must
be paid to grounding and PC board layout of ADuC836 based
designs in order to achieve optimum performance from the ADCs
and DAC.
Although the ADuC836 has separate pins for analog and digital
ground (AGND and DGND), the user must not tie these to two
separate ground planes unless the two ground planes are con-
nected together very close to the ADuC836, as illustrated in the
simplified example of Figure 64a. In systems where digital and
analog ground planes are connected together somewhere else
(at the system’s power supply, for example), they cannot be con-
nected again near the ADuC836 since a ground loop would result.
In these cases, tie the ADuC836’s AGND and DGND pins all to
the analog ground plane, as illustrated in Figure 64b. In systems
with only one ground plane, ensure that the digital and analog com-
ponents are physically separated onto separate halves of the board
such that digital return currents do not flow near analog circuitry
and vice versa.The ADuC836 can then be placed between the
digital and analog sections, as illustrated in Figure 64c.
In all of these scenarios, and in more complicated real-life appli-
cations, keep in mind the flow of current from the supplies and
back to ground. Make sure the return paths for all currents are as
close as possible to the paths the currents took to reach their des-
tinations. For example, do not power components on the analog
side of Figure 64b with DVDD since that would force return cur-
rents from DVDD to flow through AGND. Also, try to avoid digital
currents flowing under analog circuitry, which could happen if
the user placed a noisy digital chip on the left half of the board
in Figure 64c.Whenever possible, avoid large discontinuities in
the ground plane(s) (such as those formed by a long trace on the
same layer), since they force return signals to travel a longer path.
And of course, make all connections directly to the ground plane
with little or no trace separating the pin from its via to ground.
REV. A
相关PDF资料 |
PDF描述 |
|---|---|
| ADUC843BSZ62-5 | IC ADC 12BIT W/FLASH MCU 52-MQFP |
| ADUC845BCPZ62-5 | IC FLASH MCU W/24BIT ADC 56-CSP |
| ADUC847BCPZ62-5 | IC MCU FLASH W/24BIT ADC 56-CSP |
| ADV202BBCZ-135 | IC CODEC VIDEO 135MHZ 144CSPBGA |
| ADV212BBCZ-115 | IC CODEC VID JPEG 2000 121CSPBGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADUC836BCPZ-REEL | 功能描述:IC MCU 62K FLASH ADC/DAC 56LFCSP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 标准包装:38 系列:Encore!® XP® 核心处理器:eZ8 芯体尺寸:8-位 速度:5MHz 连通性:IrDA，UART/USART 外围设备:欠压检测/复位，LED，POR，PWM，WDT 输入/输出数:16 程序存储器容量:4KB（4K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:1K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 3.6 V 数据转换器:- 振荡器型:内部 工作温度:-40°C ~ 105°C 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 包装:管件 其它名称:269-4116Z8F0413SH005EG-ND |
| ADUC836BS | 制造商:Analog Devices 功能描述:MCU 8-bit ADuC8xx 8052 CISC 62KB Flash 3.3V/5V 52-Pin MQFP 制造商:Analog Devices 功能描述:8BIT MCU +16BIT DUAL ADC MQFP52 |
| ADUC836BS | 制造商:Analog Devices 功能描述:IC SEMICONDUCTOR ((NS)) |
| ADUC836BSZ | 功能描述:IC ADC DUAL 16BIT W/MCU 52-MQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 标准包装:250 系列:56F8xxx 核心处理器:56800E 芯体尺寸:16-位 速度:60MHz 连通性:CAN，SCI，SPI 外围设备:POR，PWM，温度传感器，WDT 输入/输出数:21 程序存储器容量:40KB（20K x 16） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:6K x 16 电压 - 电源 (Vcc/Vdd):2.25 V ~ 3.6 V 数据转换器:A/D 6x12b 振荡器型:内部 工作温度:-40°C ~ 125°C 封装/外壳:48-LQFP 包装:托盘 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323 |
| ADUC841 | 制造商:AD 制造商全称:Analog Devices 功能描述:MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU |
发布紧急采购，3分钟左右您将得到回复。