- 您现在的位置：买卖IC网 > PDF目录1900 > ADV3002BSTZ-RL (Analog Devices Inc)IC SWITCH HDMI/DVI 4:1 80-LQFP PDF资料下载
参数资料
| 型号： | ADV3002BSTZ-RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 9/28页 |
| 文件大小： | 0K |
| 描述： | IC SWITCH HDMI/DVI 4:1 80-LQFP |
| 产品变化通告： | Marking Change 25/Mar/2009 |
| 标准包装： | 1,000 |
| 功能： | 开关 |
| 电路： | 1 x 4:1 |
| 电压电源： | 单电源 |
| 电压 - 电源，单路/双路(±)： | 3 V ~ 3.6 V |
| 工作温度： | 0°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 80-LQFP |
| 供应商设备封装： | 80-LQFP（14x14） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
Data Sheet
ADV3002
Rev. B | Page 17 of 28
SERIAL CONTROL INTERFACE
RESET
On initial power-up, or at any point in operation, the ADV3002
register set can be restored to the default values by pulling the
RESETB pin low according to the specification in Table 3.
During normal operation, however, the RESETB pin must
be pulled up to 3.3 V.
WRITE PROCEDURE
as a microcontroller) needs to send the appropriate control
signals to the ADV3002 slave device. The signals are controlled
by the I2C master, unless otherwise specified. For a diagram of
the procedure, see Figure 32. The steps for a write procedure are
as follows:
1. Send a start condition (while holding the I2C_SCL line
high and pulling the I2C_SDA line low).
2. Send the ADV3002 part address (seven bits). The upper five
bits of the ADV3002 part address are the static value [10010]
and the two LSBs are set by Input Pins I2C_ADDR[1:0].
This transfer should be MSB first.
3. Send the write indicator bit (0).
4. Wait for the ADV3002 to acknowledge the request.
5. Send the register address (eight bits) to which data is to be
written. This transfer should be MSB first.
6. Wait for the ADV3002 to acknowledge the request.
7. Send the data (eight bits) to be written to the register
whose address was set in Step 5. This transfer should be
MSB first.
8. Wait for the ADV3002 to acknowledge the request.
9. Do one of the following:
a. Send a stop condition (while holding the I2C_SCL
line high and pulling the I2C_SDA line high) and
release control of the bus to end the transaction
(shown in Figure 32).
b. Send a repeated start condition (while holding the
I2C_SCL line high and pulling the I2C_SDA line low)
and continue from Step 2 in this procedure to perform
another write.
c. Send a repeated start condition (while holding the
I2C_SCL line high and pulling the I2C_SDA line low)
and continue from Step 2 of the read procedure (in the
Read Procedure section) to perform a read from
another address.
d. Send a repeated start condition (while holding the
I2C_SCL line high and pulling the I2C_SDA line low)
and continue from Step 8 of the read procedure (in the
Read Procedure section) to perform a read from the
same address set in Step 5 of the write procedure.
R/W
ACK
ADDR
START
FIXED ADDR PART
REGISTER ADDR
DATA
STOP
ACK
1
2
3
4
5
6
7
8
9
I2C_SCL
GENERAL CASE
I2C_SDA
EXAMPLE
I2C_SDA
07905-
012
*
*THE SWITCHING/UPDATE DELAY BEGINS AT THE FALLING EDGE OF THE LAST DATA BIT;
FOR EXAMPLE, THE FALLING EDGE JUST BEFORE STEP 8.
Figure 32. I2C Write Procedure
相关PDF资料 |
PDF描述 |
|---|---|
| ADV3003ACPZ-R7 | IC EQUALZR HDMI/DVI TMDS 40LFCSP |
| ADV3200ASWZ | IC CROSSPOINT SWIT 32X32 176LQFP |
| ADV3203ASWZ | IC CROSSPOINT SWIT 32X16 176LQFP |
| ADV3205JSTZ | IC CROSSPOINT SWIT 16X16 100LQFP |
| ADV3220ACPZ-R7 | IC MULTIPLEXER 2:1 16LFCSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADV3002-EVALZ | 制造商:AD 制造商全称:Analog Devices 功能描述:4:1 HDMI/DVI Switch with Equalization, DDC/CEC Buffers and EDID Replication |
| ADV3002XSTZ | 功能描述:IC SWITCH HDMI/DVI 4:1 80LQFP 制造商:analog devices inc. 系列:- 包装:托盘 零件状态:上次购买时间 类型:视频开关 应用:HDTV，投影仪，机顶盒 安装类型:- 封装/外壳:- 供应商器件封装:- 标准包装:1 |
| ADV3002XSTZ-RL | 功能描述:IC SWITCH HDMI/DVI 4:1 80LQFP 制造商:analog devices inc. 系列:- 包装:带卷（TR） 零件状态:上次购买时间 类型:视频开关 应用:HDTV，投影仪，机顶盒 安装类型:- 封装/外壳:- 供应商器件封装:- 标准包装:1 |
| ADV3003 | 制造商:AD 制造商全称:Analog Devices 功能描述:HDMI/DVI TMDS Equalizer |
| ADV3003ACPZ | 功能描述:IC EQUALZR HDMI/DVI TMDS 40LFCSP RoHS:是 类别:集成电路 (IC) >> 接口 - 专用 系列:- 特色产品:NXP - I2C Interface 标准包装:1 系列:- 应用:2 通道 I²C 多路复用器 接口:I²C，SM 总线 电源电压:2.3 V ~ 5.5 V 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:剪切带 (CT) 安装类型:表面贴装 产品目录页面:825 (CN2011-ZH PDF) 其它名称:568-1854-1 |
发布紧急采购，3分钟左右您将得到回复。