- 您现在的位置：买卖IC网 > PDF目录16409 > AMIS30623C6238G (ON Semiconductor)IC MOTOR DRIVER/CTLR 20-SOIC PDF资料下载
参数资料
| 型号： | AMIS30623C6238G |
| 厂商： | ON Semiconductor |
| 文件页数： | 14/61页 |
| 文件大小： | 0K |
| 描述： | IC MOTOR DRIVER/CTLR 20-SOIC |
| 标准包装： | 38 |
| 应用： | 步进电机驱动器 |
| 评估套件： | 可供 |
| 输出数： | 1 |
| 电流 - 输出： | 800mA |
| 电源电压： | 6.5 V ~ 29 V |
| 工作温度： | -40°C ~ 165°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 20-SOIC |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页
AMIS ? 30623
? The charge pump to allow driving of the H ? bridges’
high side transistors.
? Two pre ? scale 4 ? bit DAC’s to set the maximum
magnitude of the current through X and Y.
? Two DAC’s to set the correct current ratio through X
and Y.
Battery voltage monitoring is also performed by this
block, which provides the required information to the
control logic part. The same applies for detection and
reporting of an electrical problem that could occur on the
coils or the charge pump.
Control Logic (Position Controller and Main Control)
The control logic block stores the information provided by
the LIN interface (in a RAM or an OTP memory) and
digitally controls the positioning of the stepper motor in
terms of speed and acceleration, by feeding the right signals
to the motordriver state machine.
It will take into account the successive positioning
commands to properly initiate or stop the stepper motor in
order to reach the set point in a minimum time.
It also receives feedback from the motordriver part in
order to manage possible problems and decide on internal
actions and reporting to the LIN interface.
Motion Detection
Motion detection is based on the back ? emf generated
internally in the running motor. When the motor is blocked,
e.g. when it hits the end position, the velocity, and as a result
also the generated back ? emf, is disturbed. The
AMIS ? 30623 senses the back ? emf, calculates a moving
average and compares the value with two independent
threshold levels. If the back ? emf disturbance is bigger than
the set threshold, the running motor is stopped.
LIN Interface
The LIN interface implements the physical layer and the
MAC and LLC layers according to the OSI reference model.
It provides and gets information to and from the control logic
block, in order to drive the stepper motor, to configure the
way this motor must be driven, or to get information such as
actual position or diagnosis (temperature, battery voltage,
electrical status...) and pass it to the LIN master node.
Miscellaneous
The AMIS ? 30623 also contains the following:
? An internal oscillator, needed for the LIN protocol
handler as well as the control logic and the PWM
control of the motordriver.
? An internal trimmed voltage source for precise
referencing.
? A protection block featuring a thermal shutdown and a
power ? on ? reset circuit.
? A 5 V regulator (from the battery supply) to supply the
internal logic circuitry.
FUNCTIONS DESCRIPTION
This chapter describes the following functional blocks in
more detail:
? Position controller
? Main control and register, OTP memory + ROM
? Motordriver
The Motion detection and LIN controller are discussed in
separate chapters.
Position Controller
Positioning and Motion Control
A positioning command will produce a motion as
illustrated in Figure 7. A motion starts with an acceleration
phase from minimum velocity (Vmin) to maximum velocity
(Vmax) and ends with a symmetrical deceleration. This is
defined by the control logic according to the position
required by the application and the parameters programmed
by the application during the configuration phase. The
current in the coils is also programmable.
Zero Speed
Hold Current
Acceleration
range
Velocity
Vmax
Deceleration
range
Zero Speed
Hold Current
Vmin
Position
Pmin
Pstart
P=0
Figure 7. Positioning and Motion Control
http://onsemi.com
14
Pstop
Pmax
相关PDF资料 |
PDF描述 |
|---|---|
| UPM0J152MHD6TO | CAP ALUM 1500UF 6.3V 20% RADIAL |
| 012361-000 | SHIELD TERMINATOR SOLDER SLEEVE |
| VE-24Z-EV | CONVERTER MOD DC/DC 2V 60W |
| 1331-562K | INDUCTOR SHIELDED 5.60UH SMD |
| 573687-000 | SHIELD TERMINATOR |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AMIS30623C6238RG | 功能描述:马达/运动/点火控制器和驱动器 LIN STEPPER DRIVER STALL RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| AMIS30623C6239G | 功能描述:马达/运动/点火控制器和驱动器 LIN 800mA STEPPER DRIVER RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| AMIS30623C6239RG | 功能描述:马达/运动/点火控制器和驱动器 LIN 800mA STEPPER DRIVER RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| AMIS30623C623AG | 功能描述:马达/运动/点火控制器和驱动器 LIN 800mA STEPPER DRIVER RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| AMIS30623C623ARG | 功能描述:马达/运动/点火控制器和驱动器 800mA CNTRL LIN BUS MICRO STP/STALL DET RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。