- 您现在的位置：买卖IC网 > PDF目录16409 > AMIS30623C6238G (ON Semiconductor)IC MOTOR DRIVER/CTLR 20-SOIC PDF资料下载
参数资料
| 型号： | AMIS30623C6238G |
| 厂商： | ON Semiconductor |
| 文件页数： | 43/61页 |
| 文件大小： | 0K |
| 描述： | IC MOTOR DRIVER/CTLR 20-SOIC |
| 标准包装： | 38 |
| 应用： | 步进电机驱动器 |
| 评估套件： | 可供 |
| 输出数： | 1 |
| 电流 - 输出： | 800mA |
| 电源电压： | 6.5 V ~ 29 V |
| 工作温度： | -40°C ~ 165°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 20-SOIC |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页当前第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页
AMIS ? 30623
LIN Lost Before or At Power On
If the LIN communication is lost before or at power on, the
<ActPos> register does not reflect the “real” actual
position. So at LIN – lost a referencing is started using
DualPositioning. A first negative motion for half the
B
FailSafe = 1
positioner range is initiated until the stall position is reached.
The motion parameters stored in OTP will be used for this.
After this mechanical end position is reached, <ActPos>
will be reset to zero. A second motion will start to the Secure
Position also stored in OTP. More details are given below.
No
Yes
First motion of DualPosition
Half the position range
Negative direction
At Stall ? > ActPos = ‘0000’
STOP
No
SecPos ≠ 0x400
Yes
Secure Positioning
to SecPos stored in RAM,
copied from OTP
SleepEn = 1
Yes
SLEEP
No
STOP
Figure 25. Case B: LIN Lost at or During Start ? Up
If LIN is lost before or at power on, following sequence
will be followed. See Figure 25.
1. If the LIN communication is lost AND
<FailSafe> = 0, secure positioning will be
done at absolute position (stored secure position
<SecPos> .) Depending on SleepEn
AMIS ? 30623 will enter the <Stop> state or
<Sleep> state. See Table 35.
2. If the LIN communication is lost AND
<FailSafe> = 1 a referencing is started using
DualPositioning, meaning a negative motion for
half the positioner range is initiated until the stall
position is reached. The motion parameters stored
in OTP will be used for this. After this mechanical
end position is reached <ActPos> will be reset to
zero. The direction of the motion is given by the
Shaft bit .
? If <SecPos[10:0]> = 0x400:
No Second Motion will be performed.
? If <SecPos[10:0]> ≠ 0x400:
A second motion to <SecPos> is performed.
The direction is given by <SecPos[10]> in
combination with <Shaft> . Motion is done
with parameters from OTP.
Depending on SleepEn AMIS ? 30623 will enter the
<Stop> state or <Sleep> state. See Table 35.
Important Remarks:
1. The Secure Position has only a resolution of 9 bit
because only the 9 MSB’s will be copied from
OTP to RAM. See also Secure Position
2. The motion direction to SecPos is given by the
Shaft bit in OTP.
3. In case of HW2 float (= lost LIN address), the
behavior is the same as described above, except
for going to sleep mode. In that case failsafe
operation due to HW2 float is not leading to the
sleep state, otherwise the LIN communication will
wake ? up the node and cycling through POR will
occur. See also Hardwired Address HW2 .
http://onsemi.com
43
相关PDF资料 |
PDF描述 |
|---|---|
| UPM0J152MHD6TO | CAP ALUM 1500UF 6.3V 20% RADIAL |
| 012361-000 | SHIELD TERMINATOR SOLDER SLEEVE |
| VE-24Z-EV | CONVERTER MOD DC/DC 2V 60W |
| 1331-562K | INDUCTOR SHIELDED 5.60UH SMD |
| 573687-000 | SHIELD TERMINATOR |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AMIS30623C6238RG | 功能描述:马达/运动/点火控制器和驱动器 LIN STEPPER DRIVER STALL RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| AMIS30623C6239G | 功能描述:马达/运动/点火控制器和驱动器 LIN 800mA STEPPER DRIVER RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| AMIS30623C6239RG | 功能描述:马达/运动/点火控制器和驱动器 LIN 800mA STEPPER DRIVER RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| AMIS30623C623AG | 功能描述:马达/运动/点火控制器和驱动器 LIN 800mA STEPPER DRIVER RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| AMIS30623C623ARG | 功能描述:马达/运动/点火控制器和驱动器 800mA CNTRL LIN BUS MICRO STP/STALL DET RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。