- 您现在的位置：买卖IC网 > PDF目录16409 > AMIS30623C6238G (ON Semiconductor)IC MOTOR DRIVER/CTLR 20-SOIC PDF资料下载
参数资料
| 型号： | AMIS30623C6238G |
| 厂商： | ON Semiconductor |
| 文件页数： | 38/61页 |
| 文件大小： | 0K |
| 描述： | IC MOTOR DRIVER/CTLR 20-SOIC |
| 标准包装： | 38 |
| 应用： | 步进电机驱动器 |
| 评估套件： | 可供 |
| 输出数： | 1 |
| 电流 - 输出： | 800mA |
| 电源电压： | 6.5 V ~ 29 V |
| 工作温度： | -40°C ~ 165°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 20-SOIC |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页当前第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页
AMIS ? 30623
ID
Data1
Data2
Data3...
ID0
ID1
ID2
ID3
ID4
ID5
ID6
ID7
command
Physical address
Broad
Parameters...
NOTE:
<ID4> and <ID5> indicate the number of data bytes.
ID5
0
0
1
1
ID4
0
1
0
1
Ndata (number of data fields)
2
2
4
8
1. A reading frame with indirect ID must always be
consecutive to a preparing frame. It will otherwise
not be taken into account.
2. A reading frame will always return the physical
address of the answering slave node in order to
ensure robustness in the communication.
The reading frames, used with the AMIS ? 30623, are the
following:
Type #2: two, four or eight data bytes writing frame
with an identifier dynamically assigned to an
application command, regardless of the
physical address of the circuit.
Type #3: two data bytes writing frame with an
identifier dynamically assigned to a particular
slave node together with an application
command. This type of frame requires that
there are as many dynamically assigned
identifiers as there are AMIS ? 30623 circuits
using this command connected to the LIN bus.
Type #4: eight data bytes writing frame with 0x3C
identifier.
Reading Frames
A reading frame uses an in ? frame response mechanism.
That is: the master initiates the frame (synchronization field
+ identifier field), and one slave sends back the data field
together with the check field. Hence, two types of identifiers
can be used for a reading frame:
? Direct ID, which points at a particular slave node,
indicating at the same time which kind of information is
awaited from this slave node, thus triggering a specific
command. This ID provides the fastest access to a read
command but is forbidden for any other action.
? Indirect ID, which only specifies a reading command,
the physical address of the slave node that must answer
having been passed in a previous writing frame, called
a preparing frame. Indirect ID gives more flexibility
Type #5: two, four or eight Data bytes reading frame
with a direct identifier dynamically assigned to
a particular slave node together with an
application command. A preparing frame is not
needed.
Type #6: eight Data bytes reading frame with 0x3D
identifier. This is intrinsically an indirect type,
needing therefore a preparation frame. It has the
advantage to use a reserved identifier. (Note:
because of the parity calculation done by the
master, the identifier becomes 0x7D as physical
data over the bus).
Preparing Frames
A preparing frame is a frame from the master that warns
a particular slave node that it will have to answer in the next
frame (being a reading frame). A preparing frame is needed
when a reading frame does not use a dynamically assigned
direct ID. Preparing and reading frames must be
consecutive. A preparing frame will contain the physical
address of the LIN slave node that must answer in the
reading frame and will also contain a command indicating
which kind of information is awaited from the slave.
The preparing frames used with the AMIS ? 30623 can be
of type #7 or type #8 described below.
Type #7: two data bytes writing frame with
dynamically assigned identifier. The identifier
of the preparing frame has to be assigned to
ROM pointer 1000, see Table 34.
than a direct one, but provides a slower access to a read
command.
Table 31. PREPARING FRAME #7
Structure
Byte
0
Content
Identifier
Bit 7
*
Bit 6
*
Bit 5
0
Bit 4
ID4
Bit 3
ID3
Bit 2
ID2
Bit 1
ID1
Bit 0
ID0
1
2
3
Data 1
Data 2
Checksum
1
1
CMD[6:0]
AD[6:0]
Checksum over data
Where :
(*) According to parity computation
http://onsemi.com
38
相关PDF资料 |
PDF描述 |
|---|---|
| UPM0J152MHD6TO | CAP ALUM 1500UF 6.3V 20% RADIAL |
| 012361-000 | SHIELD TERMINATOR SOLDER SLEEVE |
| VE-24Z-EV | CONVERTER MOD DC/DC 2V 60W |
| 1331-562K | INDUCTOR SHIELDED 5.60UH SMD |
| 573687-000 | SHIELD TERMINATOR |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AMIS30623C6238RG | 功能描述:马达/运动/点火控制器和驱动器 LIN STEPPER DRIVER STALL RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| AMIS30623C6239G | 功能描述:马达/运动/点火控制器和驱动器 LIN 800mA STEPPER DRIVER RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| AMIS30623C6239RG | 功能描述:马达/运动/点火控制器和驱动器 LIN 800mA STEPPER DRIVER RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| AMIS30623C623AG | 功能描述:马达/运动/点火控制器和驱动器 LIN 800mA STEPPER DRIVER RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| AMIS30623C623ARG | 功能描述:马达/运动/点火控制器和驱动器 800mA CNTRL LIN BUS MICRO STP/STALL DET RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。