- 您现在的位置：买卖IC网 > PDF目录16832 > CRD5463PM-Z (Cirrus Logic Inc)REFERENCE DESIGN FOR POWER METER PDF资料下载
参数资料
| 型号： | CRD5463PM-Z |
| 厂商： | Cirrus Logic Inc |
| 文件页数： | 20/46页 |
| 文件大小： | 0K |
| 描述： | REFERENCE DESIGN FOR POWER METER |
| 标准包装： | 1 |
| 主要目的： | 电源管理，电度表/功率表 |
| 嵌入式： | 是，MCU，8 位 |
| 已用 IC / 零件： | CS5463 |
| 主要属性： | 单相功率表 |
| 次要属性： | 90 ~ 260 VAC |
| 已供物品： | 模块，适配器，线缆，电源线 |
| 其它名称： | 598-1943 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页
CS5463
The temperature update rate is a function of the number
of ADC samples. With MCLK = 4.096 MHz and K = 1
the update rate is:
5.10 System Initialization
Upon powering up, the digital circuitry is held in reset
until the analog voltage reaches 4.0 V. At that time, an
---------------------------------------- =
2240 samples
? MCLK ? K ? ? 1024
0.56 sec
eight-XIN-clock-period delay is enabled to allow the os-
cillator to stabilize. The CS5463 will then initialize.
T off = T off + ? ? T ? 2.737649 ? 10
?
The Cycle Count Register (N) must be set to a value
greater then one. Status bit TUP in the Status Register,
indicates when the Temperature Register is updated.
The Temperature Offset Register sets the zero-degree
measurement. To improve temperature measurement
accuracy, the zero-degree offset may need to be adjust-
ed after the CS5463 is initialized. Temperature-offset
calibration is achieved by adjusting the Temperature
Offset Register (T off ) by the differential temperature
( ? T) measured from a calibrated digital thermometer
and the CS5463 temperature sensor. A one-degree ad-
justment to the Temperature Register (T) is achieved by
adding 2.737649x10 -4 to the Temperature Offset Regis-
ter (T off ). Therefore,
– 4
if T off = -0.0951126 and ? T = -2.0 (°C), then
A hardware reset is initiated when the RESET pin is as-
serted with a minimum pulse width of 50 ns. The RE-
SET signal is asynchronous, with a Schmitt-trigger
input. Once the RESET pin is de-asserted, an
eight-XIN-clock-period delay is enabled.
A software reset is initiated by writing the command
0x80. After a hardware or software reset, the internal
registers (some of which drive output pins) will be reset
to their default values. Status bit DRDY in the Status
Register, indicates the CS5463 is in its active state and
ready to receive commands.
5.11 Power-down States
The CS5463 has two power-down states, Stand-by and
Sleep . In the stand-by state all circuitry except the volt-
age reference and crystal oscillator is turned off. To re-
turn the device to the active state, a power-up command
is sent to the device.
T off = ? – 0.0951126 + ? – 2.0 ? 2.737649 ? 10
– 4
? ? = – 0.09566
In Sleep state, all circuitry except the instruction decod-
er is turned off. When the power-up command is sent to
or 0xF3C168 (2’s compliment notation) is stored in the
Temperature Offset Register (T off ).
To convert the Temperature Register (T) from a Celsius
scale (°C) to a Fahrenheit scale (°F) utilize the formula
the device, a system initialization is performed (See
Section 5.10 System Initialization on page 20).
5.12 Oscillator Characteristics
XIN and XOUT are the input and output of an inverting
F = --- ? C + 17.7778 ?
o
9 o
5
amplifier configured as an on-chip oscillator, as shown
in Figure 10. The oscillator circuit is designed to work
Applying the above relationship to the CS5461A tem-
perature measurement algorithm
with a quartz crystal. To reduce circuit cost, two load ca-
pacitors C1 and C2 are integrated in the device, from
XIN to DGND, and XOUT to DGND. PCB trace lengths
should be minimized to reduce stray capacitance. To
T ? F ? = ? ? --- ? T gain ? ? T ? C ? + ? ? T off + ? 17.7778 ? 2.737649 ? 10
? ?
o 9 o
5
– 4 ?
XOUT
If T off = -0.09566 and T gain = 23.507 for a Celsius scale,
then the modified values are T off = -0.09079
(0xF460E1) and T gain = 42.3132 (0x54A05E) for a
Fahrenheit scale.
5.9 Voltage Reference
The CS5463 is specified for operation with a +2.5 V ref-
erence between the VREFIN and AGND pins. To utilize
the on-chip 2.5 V reference, connect the VREFOUT pin
to the VREFIN pin of the device. The VREFIN can be
XIN
DGND
C1
C2
Oscillator
Circuit
C1 = C2 = 22 pF
used to connect external filtering and/or references.
20
Figure 10. Oscillator Connection
DS678F3
相关PDF资料 |
PDF描述 |
|---|---|
| M1AXA-1436R | IDC CABLE - MSC14A/MC14M/X |
| 0982660228 | CBL 22POS .5MM JMPR TYPE D 1.18" |
| 301A034-4-0 | BOOT MOLDED |
| H3DDS-1418M | IDC CABLE - HKR14S/AE14M/HKR14S |
| 0982660227 | CBL 22POS .5MM JMPR TYPE A 1.18" |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CRD5490-Z | 功能描述:电源管理IC开发工具 CS5463 Pwr Meas/Mntr Reference Design RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| CRD5AS-12B | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:Reverse Conducting Thyristor Medium Power Use |
| CRD5AS-12B#B00 | 功能描述:SCR 600V 7.8A Sensitive Gate Surface Mount MP-3A 制造商:renesas electronics america 系列:- 包装:管件 零件状态:有效 电压 - 断态:600V 电压 - 栅极触发（Vgt）（最大值）:800mV 电流 - 栅极触发（Igt）（最大值）:100μA 电压 - 通态（Vtm）（最大值）:1.8V 电流 - 通态（It（AV））（最大值）:5A 电流 - 通态（It（RMS））（最大值）:7.8A 电流 - 保持（Ih）（最大值）:3mA 电流 - 断态（最大值）:2mA 电流 - 不重复浪涌 50，60Hz（Itsm）:90A @ 60Hz SCR 类型:灵敏栅极 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:TO-252-3，DPak（2 引线+接片），SC-63 供应商器件封装:MP-3A 标准包装:1 |
| CRD5AS-12BB00 | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:Reverse Conducting Thyristor Medium Power Use |
| CRD5AS-12B-T13B00 | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:Reverse Conducting Thyristor Medium Power Use |
发布紧急采购，3分钟左右您将得到回复。