参数资料
| 型号： | CS82C37A96 |
| 厂商： | Intersil |
| 文件页数： | 3/24页 |
| 文件大小： | 0K |
| 描述： | IC CMOS DMA CONTROLLER 44PLCC |
| 标准包装： | 500 |
| 应用： | CMOS DMA 控制器 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 电流 - 电源： | 2mA |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 44-LCC（J 形引线） |
| 供应商设备封装： | 44-PLCC |
| 包装： | 带卷 (TR) |
82C37A
Pin Description
PIN
SYMBOL
V CC
GND
CLK
NUMBER
31
20
12
TYPE
I
DESCRIPTION
V CC : is the +5V power supply pin. A 0.1 μ F capacitor between pins 31 and 20 is recommended for
decoupling.
Ground
CLOCK INPUT: The Clock Input is used to generate the timing signals which control 82C37A
operations. This input may be driven from DC to 12.5MHz for the 82C37A-12, from DC to 8MHz for
the 82C37A, or from DC to 5MHz for the 82C37A-5. The Clock may be stopped in either state for
standby operation.
CS
11
I
CHIP SELECT: Chip Select is an active low input used to enable the controller onto the data bus for
CPU communications.
RESET
13
I
RESET: This is an active high input which clears the Command, Status, Request, and Temporary
registers, the First/Last Flip-Flop, and the mode register counter. The Mask register is set to ignore
requests. Following a Reset, the controller is in an idle cycle.
READY
6
I
READY: This signal can be used to extend the memory read and write pulses from the 82C37A to
accommodate slow memories or I/O devices. READY must not make transitions during its specified
set-up and hold times. See Figure 12 for timing. READY is ignored in verify transfer mode.
HLDA
7
I
HOLD ACKNOWLEDGE: The active high Hold Acknowledge from the CPU indicates that it has
relinquished control of the system busses. HLDA is a synchronous input and must not transition
during its specified set-up time. There is an implied hold time (HLDA inactive) of TCH from the rising
edge of CLK, during which time HLDA must not transition.
DREQ0-
DREQ3
16-19
I
DMA REQUEST: The DMA Request (DREQ) lines are individual asynchronous channel request
inputs used by peripheral circuits to obtain DMA service. In Fixed Priority, DREQ0 has the highest
priority and DREQ3 has the lowest priority. A request is generated by activating the DREQ line of a
channel. DACK will acknowledge the recognition of a DREQ signal. Polarity of DREQ is
programmable. RESET initializes these lines to active high. DREQ must be maintained until the
corresponding DACK goes active. DREQ will not be recognized while the clock is stopped. Unused
DREQ inputs should be pulled High or Low (inactive) and the corresponding mask bit set.
DB0-DB7
21-23
26-30
I/O
DATA BUS: The Data Bus lines are bidirectional three-state signals connected to the system data
bus. The outputs are enabled in the Program condition during the I/O Read to output the contents
of a register to the CPU. The outputs are disabled and the inputs are read during an I/O Write cycle
when the CPU is programming the 82C37A control registers. During DMA cycles, the most
significant 8-bits of the address are output onto the data bus to be strobed into an external latch by
ADSTB. In memory-to-memory operations, data from the memory enters the 82C37A on the data
bus during the read-from-memory transfer, then during the write-to-memory transfer, the data bus
outputs write the data into the new memory location.
IOR
1
I/O
I/O READ: I/O Read is a bidirectional active low three-state line. In the Idle cycle, it is an input
control signal used by the CPU to read the control registers. In the Active cycle, it is an output control
signal used by the 82C37A to access data from the peripheral during a DMA Write transfer.
IOW
2
I/O
I/O WRITE: I/O Write is a bidirectional active low three-state line. In the Idle cycle, it is an input
control signal used by the CPU to load information into the 82C37A. In the Active cycle, it is an output
control signal used by the 82C37A to load data to the peripheral during a DMA Read transfer.
3
FN2967.3
October 25, 2011
相关PDF资料 |
PDF描述 |
|---|---|
| CS8363YDPSR7G | IC REG LDO 3.3V/ADJ D2PAK-7 |
| CS8391YDPR5 | IC REG LDO 5V .25A/.1A D2PAK-5 |
| D-150-0095 | CONN SPLICE BUTT BLUE/YELLOW |
| D-150-0181 | CONN SPLICE BUTT 12-14AWG YLW |
| D-150-0214 | CONN SPLICE BUTT 12-16AWG BLACK |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CS82C37AB6009 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| CS82C37AS2455 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| CS82C37AZ | 功能描述:外围驱动器与原件 - PCI PERIPH DMA CNTRLR 5V 8MHZ 44PLCC RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| CS82C50A | 制造商:未知厂家 制造商全称:未知厂家 功能描述:UART |
| CS82C50A-5 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
发布紧急采购，3分钟左右您将得到回复。