参数资料
| 型号： | CS82C37A96 |
| 厂商： | Intersil |
| 文件页数： | 9/24页 |
| 文件大小： | 0K |
| 描述： | IC CMOS DMA CONTROLLER 44PLCC |
| 标准包装： | 500 |
| 应用： | CMOS DMA 控制器 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 电流 - 电源： | 2mA |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 44-LCC（J 形引线） |
| 供应商设备封装： | 44-PLCC |
| 包装： | 带卷 (TR) |
82C37A
reprogram the two byte Address register of channel 1 when
channel 1 receives a DMA request. If the 82C37A is enabled
(bit 2 in the Command register is 0), and channel 1 is
unmasked, a DMA service will occur after only one byte of
the Address register has been reprogrammed. This
condition can be avoided by disabling the controller (setting
bit 2 in the Command register) or masking the channel
before programming any of its registers. Once the
Command Register - This 8-bit register controls the
operation of the 82C37A. It is programmed by the
microprocessor and is cleared by RESET or a Master Clear
instruction. The following diagram lists the function of the
Command register bits. See Figure 4 for Read and Write
addresses.
Command Register
programming is complete, the controller can be
enabled/unmasked.
After power-up it is suggested that all internal locations be
loaded with some known value, even if some channels are
unused. This will aid in debugging.
Register Description
Current Address Register - Each channel has a 16-bit
Current Address register. This register holds the value of the
address used during DMA transfers. The address is
automatically incremented or decremented by one after each
transfer and the values of the address are stored in the
Current Address register during the transfer. This register is
written or read by the microprocessor in successive 8-bit
bytes. See Figure 6 for programming information. It may also
be reinitialized by an Autoinitialize back to its original value.
Autoinitialize takes place only after an EOP. In memory-to-
memory mode, the channel 0 Current Address register can
be prevented from incrementing or decrementing by setting
the address hold bit in the Command register.
Current Word Count Register - Each channel has a 16-bit
Current Word Count register. This register determines the
number of transfers to be performed. The actual number of
transfers will be one more than the number programmed in
7 6 5 4 3 2 1 0
BIT NUMBER
0 Memory-to-memory disable
1 Memory-to-memory enable
0 Channel 0 address hold disable
1 Channel 0 address hold enable
X If bit 0 = 0
0 Controller enable
1 Controller disable
0 Normal timing
1 Compressed timing
X If bit 0 = 1
0 Fixed priority
1 Rotating priority
0 Late write selection
1 Extended write selection
X If bit 3 = 1
0 DREQ sense active high
1 DREQ sense active low
0 DACK sense active low
1 DACK sense active high
the Current Word Count register (i.e., programming a count
of 100 will result in 101 transfers). The word count is
decremented after each transfer. When the value in the
register goes from zero to FFFFH, a TC will be generated.
This register is loaded or read in successive 8-bit bytes by
the microprocessor in the Program Condition. See Figure 6
for programming information. Following the end of a DMA
service it may also be reinitialized by an Autoinitialization
back to its original value. Autoinitialization can occur only
when an EOP occurs. If it is not Autoinitialized, this register
will have a count of FFFFH after TC.
Base Address and Base Word Count Registers - Each
channel has a pair of Base Address and Base Word Count
registers. These 16-bit registers store the original value of
their associated current registers. During Autoinitialize these
values are used to restore the current registers to their
original values. The base registers are written
simultaneously with their corresponding current register in 8-
bit bytes in the Program Condition by the microprocessor.
See Figure 6 for programming information. These registers
cannot be read by the microprocessor.
9
Mode Register - Each channel has a 6-bit Mode register
associated with it. When the register is being written to by
the microprocessor in the Program condition, bits 0 and 1
determine which channel Mode register is to be written.
When the processor reads a Mode register, bits 0 and 1 will
FN2967.3
October 25, 2011
相关PDF资料 |
PDF描述 |
|---|---|
| CS8363YDPSR7G | IC REG LDO 3.3V/ADJ D2PAK-7 |
| CS8391YDPR5 | IC REG LDO 5V .25A/.1A D2PAK-5 |
| D-150-0095 | CONN SPLICE BUTT BLUE/YELLOW |
| D-150-0181 | CONN SPLICE BUTT 12-14AWG YLW |
| D-150-0214 | CONN SPLICE BUTT 12-16AWG BLACK |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CS82C37AB6009 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| CS82C37AS2455 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| CS82C37AZ | 功能描述:外围驱动器与原件 - PCI PERIPH DMA CNTRLR 5V 8MHZ 44PLCC RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| CS82C50A | 制造商:未知厂家 制造商全称:未知厂家 功能描述:UART |
| CS82C50A-5 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
发布紧急采购，3分钟左右您将得到回复。