- 您现在的位置：买卖IC网 > PDF目录1912 > DP83848HSQ/NOPB (National Semiconductor)IC TXRX ETHERNET PHYTER 40-LLP PDF资料下载
参数资料
| 型号： | DP83848HSQ/NOPB |
| 厂商： | National Semiconductor |
| 文件页数： | 13/82页 |
| 文件大小： | 0K |
| 描述： | IC TXRX ETHERNET PHYTER 40-LLP |
| 产品培训模块： | PHYTER® Family |
| 标准包装： | 1 |
| 类型： | 收发器 |
| 驱动器/接收器数： | 1/1 |
| 规程： | 以太网 |
| 电源电压： | 3 V ~ 3.6 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 供应商设备封装： | 40-LLP-EP（6x6） |
| 包装： | 剪切带 (CT) |
| 配用： | DP83848H-MAU-EK-ND - BOARD EVALUATION DP83848H |
| 其它名称： | *DP83848HSQ/NOPB DP83848HSQCT |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页
19
www.national.com
DP
83
84
8
H
2.5 Half Duplex vs. Full Duplex
The DP83848H supports both half and full duplex opera-
tion at both 10 Mb/s and 100 Mb/s speeds.
Half-duplex relies on the CSMA/CD protocol to handle col-
lisions and network access. In Half-Duplex mode, CRS
responds to both transmit and receive activity in order to
maintain compliance with the IEEE 802.3 specification.
Since the DP83848H is designed to support simultaneous
transmit and receive activity it is capable of supporting full-
duplex switched applications with a throughput of up to
200 Mb/s per port when operating in 100BASE-TX mode.
Because the CSMA/CD protocol does not apply to full-
duplex operation, the DP83848H disables its own internal
collision sensing and reporting functions and modifies the
behavior of Carrier Sense (CRS) such that it indicates
only receive activity. This allows a full-duplex capable
MAC to operate properly.
All modes of operation (100BASE-TX and 10BASE-T) can
run either half-duplex or full-duplex. Additionally, other
than CRS and Collision reporting, all remaining MII signal-
ing remains the same regardless of the selected duplex
mode.
It is important to understand that while Auto-Negotiation
with the use of Fast Link Pulse code words can interpret
and configure to full-duplex operation, parallel detection
can not recognize the difference between full and half-
duplex from a fixed 10 Mb/s or 100 Mb/s link partner over
twisted pair. As specified in the 802.3u specification, if a
far-end link partner is configured to a forced full duplex
100BASE-TX ability, the parallel detection state machine
in the partner would be unable to detect the full duplex
capability of the far-end link partner. This link segment
would negotiate to a half duplex 100BASE-TX configura-
tion (same scenario for 10 Mb/s).
2.6 Internal Loopback
The DP83848H includes a Loopback Test mode for facili-
tating system diagnostics. The Loopback mode is
selected through bit 14 (Loopback) of the Basic Mode
Control Register (BMCR). Writing 1 to this bit enables MII
transmit data to be routed to the MII receive outputs.
Loopback status may be checked in bit 3 of the PHY Sta-
tus Register (PHYSTS). While in Loopback mode the data
will not be transmitted onto the media. To ensure that the
desired operating mode is maintained, Auto-Negotiation
should be disabled before selecting the Loopback mode.
2.7 BIST
The DP83848H incorporates an internal Built-in Self Test
(BIST) circuit to accommodate in-circuit testing or diag-
nostics. The BIST circuit can be utilized to test the integ-
rity of the transmit and receive data paths. BIST testing
can be performed with the part in the internal loopback
mode or externally looped back using a loopback cable
fixture.
The BIST is implemented with independent transmit and
receive paths, with the transmit block generating a contin-
uous stream of a pseudo random sequence. The user can
select a 9 bit or 15 bit pseudo random sequence from the
PSR_15 bit in the PHY Control Register (PHYCR). The
received data is compared to the generated pseudo-ran-
dom data by the BIST Linear Feedback Shift Register
(LFSR) to determine the BIST pass/fail status.
The pass/fail status of the BIST is stored in the BIST sta-
tus bit in the PHYCR register. The status bit defaults to 0
(BIST fail) and will transition on a successful comparison.
If an error (mis-compare) occurs, the status bit is latched
and is cleared upon a subsequent write to the Start/Stop
bit.
For transmit VOD testing, the Packet BIST Continuous
Mode can be used to allow continuous data transmission,
setting BIST_CONT_MODE, bit 5, of CDCTRL1 (0x1Bh).
The number of BIST errors can be monitored through the
BIST Error Count in the CDCTRL1 (0x1Bh), bits [15:8].
相关PDF资料 |
PDF描述 |
|---|---|
| DP83848YB/NOPB | IC TXRX ETHERNET PHYTERA 48-LQFP |
| DRM4000-N00-232 | DRM 4000 MODULE |
| DRM4000L-N00-232 | MODULE DEAD RECKONING RS-232 |
| DS100BR111SQE/NOPB | IC REPEATER 10.3GBPS 2CH 24LLP |
| DS10BR254TSQX/NOPB | IC LVDS REPEAT 1.5GBPS 1:4 40LLP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DP83848I | 制造商:NSC 制造商全称:National Semiconductor 功能描述:Industrial Temperature Single Port 10/100 Mb/s Ethernet Physical Layer Transceiver |
| DP83848I_08 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:PHYTER? - Industrial Temperature Single Port 10/100 Mb/s Ethernet Physical Layer Transceiver |
| DP83848I-MAU-EK | 功能描述:BOARD EVALUATION DP83848I RoHS:否 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:PCI Express® (PCIe) 主要目的:接口，收发器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要属性:- 次要属性:- 已供物品:板 |
| DP83848I-MAU-EK/NOPB | 功能描述:以太网开发工具 DP83848 MAU CARD IND TEMP RoHS:否 制造商:Micrel 产品:Evaluation Boards 类型:Ethernet Transceivers 工具用于评估:KSZ8873RLL 接口类型:RMII 工作电源电压: |
| DP83848I-POE-EK | 功能描述:以太网开发工具 DP83848 POE CARD IND TEMP RoHS:否 制造商:Micrel 产品:Evaluation Boards 类型:Ethernet Transceivers 工具用于评估:KSZ8873RLL 接口类型:RMII 工作电源电压: |
发布紧急采购，3分钟左右您将得到回复。