- 您现在的位置：买卖IC网 > PDF目录1916 > DS80C410-FNY+ (Maxim Integrated Products)IC MCU 75MHZ 16MB HP 100-LQFP PDF资料下载
参数资料
| 型号： | DS80C410-FNY+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 102/102页 |
| 文件大小： | 0K |
| 描述： | IC MCU 75MHZ 16MB HP 100-LQFP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 90 |
| 系列： | 80C |
| 核心处理器： | 8051 |
| 芯体尺寸： | 8-位 |
| 速度： | 75MHz |
| 连通性： | 1 线，CAN，EBI/EMI，以太网，SIO，UART/USART |
| 外围设备： | 电源故障复位，WDT |
| 输入/输出数： | 64 |
| 程序存储器容量： | 64KB（64K x 8） |
| 程序存储器类型： | ROM |
| RAM 容量： | 64K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 1.62 V ~ 3.6 V |
| 振荡器型： | 外部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 100-LQFP |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页当前第102页
DS80C410/DS80C411 Network Microcontrollers with Ethernet and CAN
99 of 102
Status
The STATUS (C5h) register and STATUS1 (F7h) register provide information about interrupt and serial port activity
to assist in determining if it is possible to enter PMM. The microcontroller supports three levels of interrupt priority:
power-fail, high, and low. The PIP (power-fail priority interrupt status; STATUS.7), HIP (high priority interrupt status;
STATUS.6), and LIP (low priority interrupt status; STATUS.5) status bits, when set to a logic 1, indicate the
corresponding level is in service.
Software should not rely on a lower-priority level interrupt source to remove PMM (switchback) when a higher level
is in service. Check the current priority service level before entering PMM. If the current service level locks out a
desired switchback source, then it would be advisable to wait until this condition clears before entering PMM.
Alternately, software can prevent an undesired exit from PMM by intentionally entering a low priority interrupt-
service level before entering PMM. This prevents other low priority interrupts from causing a switchback.
Entering PMM during an ongoing serial port transmission or reception can corrupt the serial port activity. To
prevent this, a hardware lockout feature ignores changes to the clock divisor bits while the serial ports are active.
Serial port transmit and receive activity can be monitored through the serial port activity bits located in the STATUS
and STATUS1 registers.
Oscillator-Fail Detect
The microcontroller contains a safety mechanism called an on-chip oscillator-fail detect circuit. When enabled, this
circuit causes the microcontroller to be held in reset if the oscillator frequency falls below ~100kHz. When
activated, this circuit complements the watchdog timer. Normally, the watchdog timer is initialized so that it times
out and causes a reset in the event that the microcontroller loses control. In the event of a crystal or external
oscillator failure, however, the watchdog timer does not function, and there is the potential to fail in an uncontrolled
state. Using the oscillator-fail detect circuit forces the microcontroller to a known state (i.e., reset) even if the
oscillator stops.
The oscillator-fail detect circuitry is enabled when software sets the enable bit OFDE (PCON.4) to a 1. Please note
that software must use a timed-access procedure (described earlier) to write this bit. The OFDF (PCON.5) bit also
sets to a 1 when the circuitry detects an oscillator failure, and the microcontroller is forced into a reset state. This
bit can only be cleared to a 0 by a power-fail reset or by software. The oscillator-fail detect circuitry is not triggered
when the oscillator is stopped upon entering stop mode.
Power-Fail Reset
The microcontroller incorporates an internal precision bandgap voltage reference and comparator circuit that
provide a power-on and power-fail reset function. This circuit monitors the incoming power supply voltages (VCC1
and VCC3) and holds the microcontroller in reset if either supply is below a minimum voltage level. When power
exceeds the reset threshold, a full power-on reset is performed. In this way, this internal voltage monitoring circuitry
handles both power-up and power-down conditions without the need for additional external components.
Once VCC1 and VCC3 have risen above minimum voltages, VRST1 and VRST3 respectively, the device automatically
restarts the oscillator for the external crystal and counts 65,536 clock cycles before program execution begins at
location 0000h. This helps the system maintain reliable operation by only permitting operation when the supply
voltage is in a known good state. Software can determine that a power-on reset has occurred by checking the
power-on reset flag (POR;WDCON.6). Software should clear the POR bit after reading it.
Power-Fail Interrupt
The bandgap voltage reference that sets precise reset thresholds also generates an optional early warning power-
fail interrupt (PFI). When enabled by software, the microcontroller vectors to code address 0033h if either VCC1 or
VCC3 drop below VPFW1 or VPFW3, respectively. PFI has the highest priority. The PFI enable is in the watchdog
control SFR (EPFI;WDCON.5). Setting this bit to logic 1 enables the PFI. Application software can also read the
PFI flag at WDCON.4. A PFI condition sets this bit to a 1. The flag is independent of the interrupt enable and must
be cleared by software.
相关PDF资料 |
PDF描述 |
|---|---|
| DS8102+ | IC MODULATOR/DECODER 16-TSSOP |
| DS8113-JNG+ | IC INTERFACE SMART CARD 28-TSSOP |
| DS8313-RRX+ | IC INTERFACE SMART CARD 28-SOIC |
| DS8500-JND+T&R | IC MODEM HART SGL 3.6V 20-TQFN |
| DS87C520-ENL | IC MCU EPROM/ROM 33MH IND 44TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS80C410-FNY+ | 功能描述:8位微控制器 -MCU Network MCU w/Ethernet & CAN RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| DS80C411 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Network Microcontrollers with Ethernet and CAN |
| DS80C411-FNY | 功能描述:8位微控制器 -MCU Network MCU w/Ethernet & CAN RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| DS80C411-FNY+ | 功能描述:8位微控制器 -MCU Network MCU w/Ethernet & CAN RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| DS80CH11 | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:System Energy Manager |
发布紧急采购，3分钟左右您将得到回复。